Cub Cadet WE 26 Maintaining Your Snow Thrower, Engine, Lubrication, Shave Plate and Skid Shoes

Page 14

6

Maintaining

Your Snow

Thrower

WARNING

Before lubricating, repairing, or inspect- ing, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop.

Engine

Refer to the separate Tecumseh Engines manual packed with your unit for all engine maintenance.

Lubrication

Engine

Refer to the separate Tecumseh Engines manual packed with your unit for all engine lubrication instruc- tions.

Gear Shaft

The gear (hex) shaft should be lubricated at least once a season or after every 25 hours of operation.

1.Remove the lower frame cover by removing the two screws which secure it.

2.Apply a light coating of an all-weather multi-purpose grease to the hex shaft. See Figure 8.

Wheels

At least once a season, remove both wheels. Clean and coat the axles with a multipurpose automotive grease before reinstalling wheels.

Chute Directional Control

Once a season, the joystick should be lubricated with petroleum jelly, linseed oil, mineral oil, paraffin wax or 3-in-1 oil.

Auger Shaft

At least once a season, remove the shear pins on auger shaft. Spray lubricant inside shaft, around the spacers. Also lubricate the flange bearings found at either end of the shaft. See Figure 9.

Gear Case

The auger gear case has been filled with grease at the factory. If disassembled for any reason, lubricate with two ounces of grease (Part Number 737-0168).

NOTE: Do not overfill the gear case. Damage to the seals could result. Be sure the vent plug is free of grease in order to relieve pressure.

Figure 8

Figure 9

Avoid oil spillage on rubber friction wheel and aluminum drive plate.

Do not overfill the gear case. Damage to the seals could result.

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary. To remove skid shoes:

1.Remove the four carriage bolts and hex flange nuts which secure them to the snow thrower.

2.Reassemble new skid shoes with the four carriage bolts (two on each side) and hex flange nuts. Refer to Figure 10.

To remove shave plate:

1.Remove the carriage bolts and hex nuts which attach it to the snow thrower housing.

2.Reassemble new shave plate, making sure heads of carriage bolts are to the inside of housing. Tighten securely.

Figure 10

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents OPERATOR’S Manual Two-Stage Snow Thrower Model WECustomer Support Table of ContentsFinding and Recording Model Number Safety Labels Your ResponsibilityPractices Your Responsibility Restrict the useDo not modify engine Your ResponsibilitySetting Up Your Snow Thrower Tighten hand knobs securing upper handle to lower handleTire Pressure Chute Clean-Out ToolShear Pin Storage Operating Your Snow Thrower Know Your Snow ThrowerDrive Control/ Auger Control Lock Clean-Out ToolAuger Control Ignition KeyStarting The Engine Gas & Oil Fill-UpStopping The Engine Electric StarterAuger Control Test To Engage DriveTo Engage Augers Chute Control Making AdjustmentsShift Cable Drive Control Shift LeverSkid Shoes Auger ControlLubrication Maintaining Your Snow ThrowerEngine Shave Plate and Skid ShoesAuger Belt Replacement Drive Belt Replacement AugersFriction Wheel Removal Preparing Snow Thrower Off-Season StoragePreparing Engine Short-Term StorageThis section Addresses minor Service issues Trouble- shootingModel WE26 Or visit Parts ListTo order replacement Parts, call the Customer Dealer Referral Line atModel WE26 738-04194 Flange Shoulder Screw 452 26 13 684-04153 Page MANUFACTURER’S Limited Commercial Warranty for U.S.A CanadaMANUFACTURER’S Limited Warranty for
Top Page Image Contents