Craftsman 536.88521 To Remove Belt Cover, Screws to be Boltsto beremoved from Top removedfrom

Page 13

•Remove the gas cap.

•Remove the two bolts and nuts from the front lip of the top cover. Use a flat head screwdriver and a 3/8" wrench. See figure c,n this page.

•Remove the Idolt from the front right side. Use a 5/16" and 3/8" wrench.

•Remove the four screws on the left side of the top cover. Use a large flat head screwdriver. See figure on this page.

•Remove the bolt from the front left side. Use a 5/16" and 3/8" wrench.

•Remove the four screws on the right side of the top cover. Use a large flat head screwdriver. See figure on this page.

•Remove the three screws from the top

portion of the control panel. Use a large flat head screwdriver.

•Carefully pull up on the rear of top cover making sure to clear gas tank.

•Carefully lift top cover over the three bolts holding the lower chute to the chute ring. NOTE: This area was designed to have a tight fit, it will be necessary to rock top cover carefully over these bolts.

•Remove top cover.

•Reinstall in reverse order.

TO REMOVE BELT COVER

•Follow these steps from operator's position.

•Remove the four bolts and nuts holding

the belt cover to the auger housing. Use a 5/16" and 3/8" wrench.

•Remove the two screws holding the belt cover to the top cover. Use a large flat head screwdriver. NOTE: If the top cover is already removed, omit this step.

•Remove the one screw holding the belt

cover to the bottom cover. Use a large flat head screwdriver.

•Grasp the bottom portion of the belt cover and pull down and out to remove.

•Reinstall in reverse order.

Screws to be

Boltsto beremoved from Top removedfrom

T,

Cover

Chute

Fasteners

Lower Chute

tobe

removed from removed

Belt Cover fromBelt

Cover

TO ADJUST BRAKE PAD

The brake pad isadjusted at the factory and no periodic adjustment is necessary.

IMPORTANT: Adjustment should only be made to the brake if the brake pad has become loose or has been removed. To adjust proceed as follows:

NOTE: See figure on next page for proper location of brake pad.

•Tum engine off.

•Remove belt cover. See To Remove Belt Cover paragraph on this page.

•Remove the top cover. See To Remove Top Cover instructions on page 12-13.

NOTE: Make sure the belt is in proper position. See To Replace the Drive Belt paragraph on page 14.

•Tie the control bail to the upper handle with a piece of string. NOTE: This will engage the pulley and belt system.

•Using a 7/16•wrench, 7/16 socket, and a rachet loosen screw and nut on brake

pad. See first figure on page 14 for location of screw and nut.

•Adjust brake pad up or down to have a 1/8" gap between the bottom of the brake pad and the belt.

•Tighten screw and nut.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 761893 07/27/98 SEARS, Roebuck and CO., Hoffman Estates, IL 60179 U.S.AEngine exhaust from this product Limited TWO-YEAR Warranty on Craftsman Snow ThrowerBefore USE Deadly GAS Fuel SafetySafe Storage REPAIR/ADJUSTMENTSSAFETY All assembly instructions have been Completed ChecklistTo Remove Snow Thrower from Carton To Assemble the Snow ThrowerChokeButton Chute Control Lower Handle Chute DeflectorPrimer Button Injects fuel directly into To USE Auger Propel Action S. I Imperzal s.I. MetricBefore Starting Engine Fill GASTo Stop Engine Gasoline and OIL MixtureTo Start Engine Electric Start Cold StartWarm Start To Stop EngineTo Start Engine Recoil Start DRY and Average Snow Product SpecificationsWET Packed Snow Snow Throwing TipsLubrication Chart Lubrication AS Required Customer Responsibilities ServiceRecords Spark PlugTo Adjust the Chute Crank Assembly Carburetor AdjustmentTo Adjusttheaugercontrol Cable To Remove TOP CoverTo Remove Belt Cover To Adjust Brake PADScrews to be Boltsto beremoved from Top removedfrom To Replace the Auger To Replace the Drive BeltLeft F#ame Engine Service Push the spark plug wire onto the spark plugAdjust Engine Speed Engine Storage Snow Thrower StorageCarbu Drain Right side view Engine OtherTrouble Adjust auger control cableCorrection CauseCraftsman 21 5H.P. Snow Thrower Electric Start AssemblyPart Name Oraftsman 21 5H.P. Snow Thrower ENGINE/DRIVE AssemblyPart Name Discharge Chute Assembly Frame AssemblyBelt Cover Assembly 52010 481540 51oHandle Assembly Craftsman 21 -5H.P.SNOW Thrower Wheel AssemblyPartname Part Name Decals Craftsman 21 5H.P. Snow ThrowerPart Name Partno Craftsman 2-CYCLE Engine Model Number Model Number Throttle Shutter REF. PART# Part NameStarter Rewind Starter noRetainer Pinion Driver Dust WasherANTI-DRIFT Part

536.88521 specifications

The Craftsman 536.88521 is a versatile and powerful snow blower, designed to efficiently tackle heavy snowfall and keep pathways and driveways clear during winter months. With a strong focus on usability and performance, this model is favored by homeowners looking for reliable equipment that can handle various snow conditions.

One of the key features of the Craftsman 536.88521 is its 24-inch clearing width, which allows for quick and efficient snow removal. The robust auger design ensures that even heavy, wet snow can be efficiently thrown aside, making it suitable for various climates and snow types. The powerful 179cc engine provides ample power, allowing the snow blower to clear deep snow without straining.

Ergonomically designed, the Craftsman 536.88521 includes adjustable handles that promote comfortable operation while reducing fatigue during extended use. The easy-to-use controls are conveniently located, enabling users to adjust speed settings and the direction of the snow discharge without having to stop. The model features a 180-degree rotating chute that allows for precise snow placement, which is essential for maintaining clean walkways and driveways.

Technology is integral to the Craftsman 536.88521, featuring electric start capabilities for hassle-free ignition, eliminating the need for strenuous pull-starts in cold conditions. Additionally, the snow blower is equipped with a heavy-duty scraper blade that ensures efficient clearing down to the pavement, reducing the chances of ice buildup.

Another notable characteristic of the Craftsman 536.88521 is its durable construction. Built with high-quality materials, it is designed to withstand harsh winter conditions, ensuring longevity and reliability over time. The snow blower's large, enhanced tires provide excellent traction and maneuverability, allowing users to navigate through tough snow conditions with ease.

Overall, the Craftsman 536.88521 stands out as a dependable snow blower, combining power, efficiency, and user-friendly features. Its versatility makes it an excellent choice for homeowners looking to maintain clear and safe outdoor areas during winter storms. With the right balance of technology and practicality, it promises an effective solution for winter snow removal tasks.
Top Page Image Contents