To Remove Snow Thrower from Carton, Checklist

Craftsman 536.88521 To Remove Snow Thrower from Carton, Checklist, To Assemble the Snow Thrower

Page 5

CAUTION" Always wear safety

glasses or eye shields while assembling snow thrower.

TOOLS REQUIRED FOR ASSEMBLY 1 - Knife to cut carton

The figure to the right shows the snow thrower completely assembled. References to the right or left hand side

of the snow thrower are from the viewpoint of the operator'sposition behind the unit.

TO REMOVE SNOW THROWER FROM CARTON

•Locate and remove container of Crafts- man 2-cycle oil.

•Remove the inserts positioned around the unit and the packing material.

•Cut down all four corners and lay the panel down flat.

•Remove and discard bottom packaging.

•Pull snow thrower out of the carton.

CHECKLIST

Before you operate your new snow thrower, to ensure that you receive the best perfor- mance and satisfaction from this quality product, please review the following checklist:

_/ All assembly instructions have been

completed.

The discharge chute rotates freely.

No remaining loose parts in carton. While learning how to use your snow

thrower, pay extra attention to the following important items:

_/_/ Make sure gas tank is filled with the 40:1 ratio mixture of gasoline and oil.

_/_/ Become familiar with all controls-their

location and function. Operate controls before starting engine.

TO ASSEMBLE THE SNOW

THROWER

• Remove wrap on upper handle and alongOperatin i Position

the side of both handles.Discard wrap.

• Unfold upper handle to remove

	packaging on the control panel and
	discard.		Chute Control Rod
			Chute Control Rod
•	Loosen the tee knobs on each side of the		\
•	Loosen the tee knobs on each side of the
	upper handle.
•	Raise the upper handle to the operating		Tee Knob
	position.	Chute Deflector

NOTE: Make sure the cable is not caught between the upper and lower handle.

•Check to be sure the clutch cable is not caught in the handle.

•Tighten tee knobs.

Image 5

Contents

761893 07/27/98 SEARS, Roebuck and CO., Hoffman Estates, IL 60179 U.S.ABefore USE Limited TWO-YEAR Warranty on Craftsman Snow ThrowerEngine exhaust from this product Safe Storage Fuel SafetyDeadly GAS REPAIR/ADJUSTMENTSSAFETY All assembly instructions have been Completed ChecklistTo Remove Snow Thrower from Carton To Assemble the Snow ThrowerPrimer Button Injects fuel directly into Chute Control Lower Handle Chute DeflectorChokeButton To USE Auger Propel Action S. I Imperzal s.I. MetricBefore Starting Engine Fill GASTo Stop Engine Gasoline and OIL MixtureTo Start Engine Electric Start Cold StartTo Start Engine Recoil Start To Stop EngineWarm Start DRY and Average Snow Product SpecificationsWET Packed Snow Snow Throwing TipsLubrication Chart Lubrication AS Required Customer Responsibilities ServiceRecords Spark PlugTo Adjust the Chute Crank Assembly Carburetor AdjustmentTo Adjusttheaugercontrol Cable To Remove TOP CoverScrews to be Boltsto beremoved from Top removedfrom To Adjust Brake PADTo Remove Belt Cover Left F#ame To Replace the Drive BeltTo Replace the Auger Adjust Engine Speed Push the spark plug wire onto the spark plugEngine Service Engine Storage Snow Thrower StorageCarbu Drain Right side view Engine OtherTrouble Adjust auger control cableCorrection CausePart Name Electric Start AssemblyCraftsman 21 5H.P. Snow Thrower Part Name ENGINE/DRIVE AssemblyOraftsman 21 5H.P. Snow Thrower Discharge Chute Assembly Frame AssemblyBelt Cover Assembly 52010 481540 51oPartname Part Name Craftsman 21 -5H.P.SNOW Thrower Wheel AssemblyHandle Assembly Part Name Partno Craftsman 21 5H.P. Snow ThrowerDecals Craftsman 2-CYCLE Engine Model Number Model Number Throttle Shutter REF. PART# Part NameRetainer Starter noStarter Rewind ANTI-DRIFT Dust WasherPinion Driver Part

Craftsman 536.88521 To Remove Snow Thrower from Carton, Checklist, To Assemble the Snow Thrower