Craftsman 536.88521 To Stop Engine, Warm Start, To Start Engine Recoil Start

Page 9

•As engine warms up and begins to operate evenly, move the choke control slowly to the OFF position. If the engine falters, turn to 1/2 choke until it runs smoothly, then move to OFF position.

NOTE: Allow the engine.to warm up for a few minutes before using snow thrower, as the engine will not develop full power until it reaches operating temperature.

WARM START

•Be sure the choke is in the OFF posi- tion and pull the starter handle until the engine starts.

•Do not prime a warm engine. If the en- gine fails to start, follow the Cold En- gine Start instructions on page 8.

Recoil Starter

Primer Button Handle

oo

Choke Control

Electric Start

Switch Box

Button

Z_ CAUTION: This starter is equipped to operate on 120 volt AC household current. Follow all instructions carefully as set forth in the "To Start Engine" section. When

connecting 120 volt AC power cord, always connect the cord to the switch box on the

engine first, then plug the other end into the household receptacle. When disconnecting the 120 volt AC power cord, always unplug from the household receptacle first.

TO STOP ENGINE

•To stop the engine, turn the key to OFF and remove key. Keep key in a safe place. The engine will not start without the key. See figure above.

TO START ENGINE (RECOIL START)

Before starting the engine, be certain that you have read and understood all the

instructions on the preceding pages.

COLD START

•Insert the key and turn ON.

•Move the choke control to the FULL position.

•Push the primer button while covering the vent holes as follows: (Remove finger from primer button between primes).

One time if temperature is above 50°F. Two times if temperature is 50 ° F to 15°F. Four times if temperature is below 15°F.

•Pull the starter handle with a smooth rapid movement. Do not allow the starter rope to snap back. Rewind smoothly while holding the starter handle. If the engine fires but does not start, pull the starter handle until the engine starts.

•Afterthree pulls, repeat the priming and pulling steps again.

•As engine starts warms up move choke lever to "1/2 choke" position. When engine runs smoothly, move choke lever to "No Choke" Position

NOTE: Allow the engine to warm up for several minutes before blowing snow in temperatures below 0°F.

WARM START

•Be sure the choke is in the OFF posi- tion and pull the starter handle until the engine starts.

•Do not prime a warm engine. If the en- gine fails to start, follow the Cold En- gine Start instructions on page 8.

/_ CAUTION: Never run engine indoors or in enclosed, poody ventilated areas.

Engine exhaust contains carbon monoxide, an odorless and a deadly gas. Always stand behind snow thrower(operator's position) when starting engine. Do not put hands, feet, hair or loose clothing in or near the discharge chute deflector or auger housing while the engine is running. The tempera- ture of the muffler and neaby areas may exceed 150 ° _; avoid these areas also.

,&

LL_ WARNING: Objects such as gravel, rocks or other debris, if struck by the auger, may be thrown with sufficient force to cause personal injury or property damage.

We recommend standard safety glasses or Wide Vision Safety Mask for over your glasses.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 761893 07/27/98 SEARS, Roebuck and CO., Hoffman Estates, IL 60179 U.S.ALimited TWO-YEAR Warranty on Craftsman Snow Thrower Engine exhaust from this productBefore USE Fuel Safety Deadly GASSafe Storage REPAIR/ADJUSTMENTSSAFETY All assembly instructions have been Completed ChecklistTo Remove Snow Thrower from Carton To Assemble the Snow ThrowerChute Control Lower Handle Chute Deflector ChokeButtonPrimer Button Injects fuel directly into To USE Auger Propel Action S. I Imperzal s.I. MetricBefore Starting Engine Fill GASTo Stop Engine Gasoline and OIL MixtureTo Start Engine Electric Start Cold StartTo Stop Engine Warm StartTo Start Engine Recoil Start DRY and Average Snow Product SpecificationsWET Packed Snow Snow Throwing TipsLubrication Chart Lubrication AS Required Customer Responsibilities ServiceRecords Spark PlugTo Adjust the Chute Crank Assembly Carburetor AdjustmentTo Adjusttheaugercontrol Cable To Remove TOP CoverTo Adjust Brake PAD To Remove Belt CoverScrews to be Boltsto beremoved from Top removedfrom To Replace the Drive Belt To Replace the AugerLeft F#ame Push the spark plug wire onto the spark plug Engine ServiceAdjust Engine Speed Engine Storage Snow Thrower StorageCarbu Drain Right side view Engine OtherTrouble Adjust auger control cableCorrection CauseElectric Start Assembly Craftsman 21 5H.P. Snow ThrowerPart Name ENGINE/DRIVE Assembly Oraftsman 21 5H.P. Snow ThrowerPart Name Discharge Chute Assembly Frame AssemblyBelt Cover Assembly 52010 481540 51oCraftsman 21 -5H.P.SNOW Thrower Wheel Assembly Handle AssemblyPartname Part Name Craftsman 21 5H.P. Snow Thrower DecalsPart Name Partno Craftsman 2-CYCLE Engine Model Number Model Number Throttle Shutter REF. PART# Part NameStarter no Starter RewindRetainer Dust Washer Pinion DriverANTI-DRIFT Part

536.88521 specifications

The Craftsman 536.88521 is a versatile and powerful snow blower, designed to efficiently tackle heavy snowfall and keep pathways and driveways clear during winter months. With a strong focus on usability and performance, this model is favored by homeowners looking for reliable equipment that can handle various snow conditions.

One of the key features of the Craftsman 536.88521 is its 24-inch clearing width, which allows for quick and efficient snow removal. The robust auger design ensures that even heavy, wet snow can be efficiently thrown aside, making it suitable for various climates and snow types. The powerful 179cc engine provides ample power, allowing the snow blower to clear deep snow without straining.

Ergonomically designed, the Craftsman 536.88521 includes adjustable handles that promote comfortable operation while reducing fatigue during extended use. The easy-to-use controls are conveniently located, enabling users to adjust speed settings and the direction of the snow discharge without having to stop. The model features a 180-degree rotating chute that allows for precise snow placement, which is essential for maintaining clean walkways and driveways.

Technology is integral to the Craftsman 536.88521, featuring electric start capabilities for hassle-free ignition, eliminating the need for strenuous pull-starts in cold conditions. Additionally, the snow blower is equipped with a heavy-duty scraper blade that ensures efficient clearing down to the pavement, reducing the chances of ice buildup.

Another notable characteristic of the Craftsman 536.88521 is its durable construction. Built with high-quality materials, it is designed to withstand harsh winter conditions, ensuring longevity and reliability over time. The snow blower's large, enhanced tires provide excellent traction and maneuverability, allowing users to navigate through tough snow conditions with ease.

Overall, the Craftsman 536.88521 stands out as a dependable snow blower, combining power, efficiency, and user-friendly features. Its versatility makes it an excellent choice for homeowners looking to maintain clear and safe outdoor areas during winter storms. With the right balance of technology and practicality, it promises an effective solution for winter snow removal tasks.
Top Page Image Contents