Craftsman 486.24838 manual Skid Shoe Adjustment, Lift Release Cable Adjustment, Spiral Augers

Page 29

CAUTION: Beforeservicingoradjusting thesnowthrowershutofftheengine,remove thesparkplugwire(s),settheparkingbrake andr_movethekeyfromthetractorignition.

REPLACING AUGER BELT

•Disengage the tractor's attachment clutch.

•Lower the snow thrower to the ground.

•Remove the attachment pin

•Lock the snow thrower's lift handle in the down position to decrease belt tension

•Release the spring tension from the auger belt idler arm on the bottom of the clutchddler assembly.

•Remove the auger drive belt from the clutch/idler assembly and from the spgal auger housing

•Install new belt over top of large auger drive pulley and under the two side idler pulleys Twist the belt 1/4 turn to seat the "V" of the belt in the groove of each idler pulley. Refer to figure 55 on page 23

•Assemble the belt onto the clutch/idler assembly

SKID SHOE ADJUSTMENT

*The skid shoes are mounted on each side of the spiral auger housing. They regulate the distance the scraper plate is raised above the plowing surface. When removing snow from a gravel driveway or and uneven surface, it is advisable to keep the scraper plate as high above the surface as possible to prevent possible damage to the spiral auger On blacktop or concrete surface, keep the scraper plate as close to the surface as possible

,Raise the snow thrower off the ground and place a block under each end of the scraper plate Loosen the six hex nuts securing the skid shoes to the housing Adjust the skid shoes up or down and retighten the nuts securely. Adjust both skid shoes to the same height to keep the housing and the scraper plate level See figure 64

FIGURE 64

LIFT RELEASE CABLE ADJUSTMENT

•If the lift rod does not lock the snow thrower securely in the transport position, loosen the upper hex nut on the lift bracket a few turns and tighten the lower hex nut. Refer to figure 48 on page 21

If the lift rod fails to unlock completely to lower the snow thrower, loosen the lower hex nut on the lift bracket a few turns and tighten the upper hex nut Refer to figure 48 on page 21

CLUTCH DISENGAGEMENT ADJUSTMENT

(For tractors with engagement rod clutches only. Not for electric clutches or cable clutches)

if the spiral auger on the snow thrower does not stop when the attachment clutch lever on the tractor is

disengaged, then adjustment is necessary. Proceed as foNows. Refer back to figure 33 on page 16.

•Place the attachment clutch lever in the disengaged position.

•Remove the hairpin cotter from the engagement rod trunnion and lift the trunnion out of the hole in the idler

arm

Screw the trunnion a few turns towards the front end of the rod

Replace the trunnion into the hole in the idler arm and secure it with the hairpin cotter

Check the operation of the snow thrower If the spiral augers still do not stop, repeat the above steps until the augers stop when the attachment dutch lever is placed in the disengaged position

SPIRAL AUGERS

,The spiral augers are secured to the auger shaft with two shear bolts and nylock nuts If you hit a foreign object or if ice jams the augers, the snow thrower is designed so that the bolts will shear

•If the augers wilt not turn, check to see if the shear bolts have sheared See figure 65 Two replacement shear bolts and nyiock nuts have been provided with the snow thrower. For future use order part number 710-0890A shear bolt and number 47810 nylock nut

GEAR HOUSING

SHEAR BOLT AND

SCRAPER

SKID

HEX

LOCK NUT

PLATE

SHOE

 

 

 

FIGURE

65

 

 

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Crqftsnqn Sears, Roebuck and Co., D817WA, Hoffmn Estates, IL Exercisecautionatalltimes,whenusingpowerequipment Shown Actual SiZE Not Shown Actual SiZEQTY Description Belt,AugerAttachedtoHousingAssembly Additional Items Required Right Bide View Engine MountingPlate If your tractor has an electric attachment clutch go to on Manual Attachment ClutchSee Figure 16 x 3/4Pulley Attach Clutch Idler Assemblyto TractorViewed from Left Side Tractor Type t Deck SiZE Clutch Type LeftSEEFIGURE17 CLUTCH/IDLER Assembly Pulley Hairpin Cotter KKRight See NoteWasherss \ I Thread Forming 3 3/8 LockRight Side View On Tractors With Foot Rest BracketsH.&NGER Tractorsclutch ARM Engagement ROD Installing CLUTCH/IDLER AssemblyGo to on Tractors Clutch Cable Carriage Bolt OCotter PIN JJ Hairpin Cotter See Figure Tractor Type Deck Size See TableKeeper Hairpin Cotter KK See FigureTrigger Assembly ROD Chute CrankLeft 81DEVIEW Chute Keeper HHTwist Attaching Weight Tray to Tractor Installing the Attachment PIN Refer Sackto onSetting the Auger Belt Tension See Figure CC Tighten all loose bolts at this time Attachingtogtgarden Tractors with aOriginal CrossAlternate Instructions for Weigrttray see Figure Attaching KEG to WeighttrayHitch Attach Reflectors to Rear FenderControlling Snow Discharge Skid ShoeLubrication Customer ResponsibilitiesCheck Scraper and Shoes for Wear 65 onLift Release Cable Adjustment Skid Shoe AdjustmentClutch Disengagement Adjustment Spiral AugersProblem Cause CORRI=CTION Removing the Spiral Auger HousingStorage Recommendations Parts to Remove AT END of SeasonPage Page Page Repair Parts for Model 486.24838 42 Snowthrower QTY. Description Part QTY Description REE820 7879 QTY Description REE Part REF Part NO. noRepair Parts for Model Suggested Guide for Sighting Slopes for Safe Operation MY-HOME

486.24838 specifications

The Craftsman 486.24838 is a powerful and versatile tool, designed to meet the demands of both homeowners and professional landscapers. This versatile machine is particularly noted for its performance in lawn maintenance and is a favorite among gardening enthusiasts.

One of the key features of the Craftsman 486.24838 is its robust engine, which boasts impressive horsepower. This power is essential for tackling tough terrains and thick grass, ensuring reliable operation under various conditions. The engine is designed for efficiency, promoting fuel economy without sacrificing performance. It starts easily, providing users with a hassle-free experience every time they need to fire it up.

Another standout feature is the machine's cutting deck. The Craftsman 486.24838 is equipped with a wide, durable cutting deck that facilitates efficient mowing. This feature allows users to cover larger areas in less time, making it ideal for spacious lawns or commercial properties. The cutting height is adjustable, permitting users to customize their mowing experience to suit different grass types and lengths.

In addition to its powerful engine and cutting capabilities, the Craftsman 486.24838 incorporates cutting-edge technologies aimed at enhancing its usability. The unit comes with ergonomic handles that improve comfort during operation, reducing fatigue during prolonged use. The intuitive controls are easy to reach and operate, making it simple for users of all skill levels to navigate.

Moreover, the machine is equipped with high-quality, durable wheels that provide superior traction and stability on uneven terrain. This feature allows users to maintain control over the equipment, ensuring it can handle inclines and rough patches with ease.

The Craftsman 486.24838 is designed for longevity and user-friendly maintenance. The robust construction materials ensure that it withstands the rigors of regular use, while its easy-access maintenance points facilitate quick adjustments and upkeep.

Overall, the Craftsman 486.24838 is an excellent choice for those looking for a reliable, efficient, and user-friendly landscaping tool. It combines powerful performance with advanced features, making it suitable for both residential and commercial landscaping tasks. Whether you're maintaining a large estate or a modest backyard, this machine is designed to deliver results.
Top Page Image Contents