Craftsman 247.88853 owner manual Operating Snow Thrower

Page 15

•Make sure that the auger drive and the traction drive levers are in the disengaged RELEASED position.

•Move throttle control lever to FAST position.

•Remove the keys from the plastic bag. Push key into the ignition slot. Make sure it snaps into place. Do not turn key. Keep the second key in a safe place.

•Rotate the choke knob to FULL choke position.

•Connect the power cord to the switch box on the engine.

•Plug the other end of the power cord into a three-hole, grounded 120 volt A.C. receptacle.

WARNING: Do not use primer while starting the engine with an electric starter.

•Push down on the starter button until the engine starts. Do not crank for more than 10 seconds at a time. This electric starter is thermally protected. If overheated, it will stop automatically and can be restarted only when it has cooled to a safe temperature (a wait of about 5 to 10 minutes is required).

•When the engine starts, release the starter button and slowly rotate the choke to OFF position. If the engine falters, rotate the choke to FULL and then gradually to OFF.

•Disconnect the power cord from the receptacle first and then from the switch box on the engine.

•Allow the engine to warm up for a few minutes because the engine will not develop full power until it reaches operating temperature.

•Operate the engine at full throttle (FAST) when throwing snow.

Warm Start

•If restarting a warm engine after a shut down, rotate choke to OFF instead of FULL and press the starter button.

B. Recoil Starter

Make sure that the engine has sufficient oil and the auger drive and the traction drive levers are released.

•Move throttle control to FAST position.

•Push key into the ignition slot so that it snaps into place. Do not turn key. Remove plastic bag and keep the second key in a safe place.

•Rotate choke control to FULL choke position.

•Push the primer button while covering the vent hole. Remove your finger from the primer between primes. Do not prime if temperature is above

50o F; prime two times between 50o F and 15o F; and prime four times below 15o F.

•Pull the starter handle rapidly. Do not allow the handle to snap back, but allow it to rewind slowly while keeping a firm hold on the starter handle.

•As the engine warms up and begins to operate evenly, rotate the choke knob slowly to OFF position. If the engine falters, return to FULL choke, then slowly move to OFF choke position.

•Allow the engine to warm up for a few minutes because the engine will not develop full power until it reaches operating temperature.

•Operate the engine at full throttle (FAST) when throwing snow.

Warm Start

•If restarting a warm engine after a temporary shut down, rotate choke to OFF instead of FULL and do not prime. Press the starter button.

Frozen Recoil Starter

If the starter is frozen and will not turn the engine, proceed as follows:

•Pull as much rope out of the starter as possible.

•Release the starter handle and let it snap back against the starter.

•If the engine still fails to start, repeat the first two steps. If continued attempts do not free starter, follow the electric starter procedures to start.

•Avoid possible freezing of recoil starter and the engine controls.

Operating Snow Thrower

To Engage Drive

•With the engine running near top speed, move shift lever to one of six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist. Use slower speeds until you are familiar with the operation of the snow thrower.

•Squeeze the traction drive clutch grip against the right handle and the snow thrower will move. Release it and the drive motion will stop.

To Engage Augers

•To engage the augers and start snow throwing, squeeze the left hand auger clutch grip against the left handle. Release to stop augers.

•While the auger control is engaged, squeeze the traction drive control to move, release to stop. Do not shift speeds while the drive is engaged.

NOTE: This same lever also locks the auger control so you can turn the chute crank without interrupting the snow throwing process.

•Release the auger control; the interlock mechanism should keep the auger control engaged until the traction drive control is released.

•Release the traction drive control to stop both the augers and the wheel drive.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.A 247.888530Warranty Information Table of ContentsTraining Safe Operation PracticesMaintenance and Storage Hardware Pack Loose Parts AssemblyAttaching Handle Assembly Removing From CartonChute Hex Bolt Hex Flange Nut Keeper Attaching ChuteAttaching Chute Crank Lock Washer Hex Bolt Right Handle TabSupport Hex Bolt Upper Chute Crank Bracket Lower Chute Carriage Bolt Crank Bracket Hex Lock NutCable Guide Outer portion Fitting Cut-out Attaching Clutch CablesAttaching Shift Rod Attaching Turn TriggersLamp Wiring Trigger Cable Handle Alternator Lamp Lead Wire SlotSecure with screw Weld Nut Turn Skid Shoe Final AdjustmentsAuger Control Traction Drive Clutch and Shift LeverMeets Ansi Safety Standards OperationKnowing Your Snow Thrower Operating Controls Stopping Snow ThrowerBefore Starting Engine Cold Start To Start EngineStarting Instructions At a Glance Electric StarterOperating Snow Thrower To Stop The Snow Thrower To Throw SnowOperating Tips Before StoppingCustomer Responsibilities MaintenanceClean snow thrower Clean skid shoes Clean shave plate General RecommendationsCheck Friction Wheel Engine MaintenanceLubrication Check V-beltsSpark Plug Viscosity ChartChecking Oil Level Changing OilAdjustments Service & AdjustmentsShave Plate And Skid Shoes ServiceCarburetor AugersHex Nut Lock Washer PushChanging Friction Wheel Rubber Drive BeltSprocket Spacer Hex Shaft Hex Hub CarburetorCarburetor Bowl Drain OFF-SEASON StoragePreparing Engine Preparing Snow ThrowerTrouble Possible Causes Corrective Action TROUBLE-SHOOTINGLabels MAP Repair Parts Sears Craftsman 9.0 H.P. Snow Thrower Model Polo Green Powder Black Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower 298 130B 301 396 340 300 264A 400 310 Key Part Description Qty Recoil Starter Carburetor Garantia DE Información Especificaciones Del ProductoNumero De Modelo Entrenamiento Practicas Seguras DE OperacionMantenimiento Y Almacenamiento Piezas de Repuesto Conjunto DE Ferreteria DE FerreteriaHerramientas Requeridas EnsambladoExtraccion De La Unidad De La Caja Piezas SueltasFijacion De La Manivela De La Canaleta Fijacion De La CanaletaManija Canaleta Superior Cable De laManija inferior de la canaleta Fijacion De Los Cables Del Embrague Fijacion De La Vara De CambiosCableado de la Lámpara Fijacion De Los Gatillos De GiroAjuste de la Zapata Deslizante Ajustes FinalesAjuste del Control de la Hélice Ajuste del Control del Propulsor de TracciónControl de la helice Palanca De CambiosOperacion Conozca Su Expulsor De NieveArranque Del Motor Detencion Del Expulsor De NieveLlenado De Gasolina Y Aceite Arrancador eléctricoComo Apagar El Motor Para Enganchar El PropulsorEnganche De La Propulsion Enganche De Las Espirales Sin Fin Presion De La RuedasConsejos De Operacion Manejo De La Limpiadora De NieveLubricacion Mecanismo De CambiosMantenimiento Recomendaciones GeneralesMantenimiento del Motor Ajustes Service & AjustesCorreas de la espiral sin fin ServiceHelices Reemplazo De La CorreaNota Sea precavido para evitar apretar el cable de control Cubrierta del propulsor Correa propulsoraPinon Separador Eje hexagonal Cubo hexagonal del pinon Almacenamiento DE Fuera DE Temporada Preparación del motorPreparación del Expulsor de Nieve Tabla DE Localizacion DE Fallas Problema Causas posible Accion correctoraYour Notes/Vuestro Apuntes Para pedir servicio de reparación a domicillio U.S.A. or Canada For in-home major brand repair serviceFor the repair or replacement parts you need To purchase or inquire about a Sears Maintenance Agreement

247.88853 specifications

The Craftsman 247.88853 is a renowned model in the realm of outdoor power equipment, particularly known for its robust design and high functionality. This versatile machine is primarily designed to provide users with an efficient lawn mowing experience while ensuring ease of use and maintenance.

One of the standout features of the Craftsman 247.88853 is its powerful engine. Equipped with a 24 HP V-twin gas engine, it delivers reliable performance for demanding mowing tasks. This powerful engine not only enhances cutting efficiency but also ensures that the mower can tackle tougher terrains with ease. Moreover, the engine operates smoothly, resulting in less vibration and noise, which makes for a more pleasant mowing experience.

The cutting system of the Craftsman 247.88853 is another significant characteristic that sets it apart. Featuring a 50-inch cutting deck, it provides a wide mowing path, significantly reducing the time spent on lawn maintenance. The deck is made of durable materials, ensuring longevity and resilience against the wear and tear of heavy use. Additionally, the height adjustment feature allows users to set the cutting height with precision, accommodating various grass types and desired lawn finishes.

In terms of user comfort and control, the Craftsman 247.88853 does not disappoint. It comes equipped with an ergonomic seat that provides ample support for long mowing sessions. Furthermore, the easy-to-use hydrostatic transmission enables smooth and effortless speed control, allowing users to navigate their lawns with agility.

The mower is designed with modern technologies that enhance its usability and efficiency. The inclusion of a built-in mulching capability is one such technology, which allows the grass to be finely chopped and returned to the lawn as natural fertilizer. This eco-friendly feature supports sustainability while promoting healthier lawn growth.

Lastly, maintenance and serviceability are made easier with the Craftsman 247.88853. The mower features a straightforward design that simplifies tasks such as oil changes, blade sharpening, and general upkeep. This focus on ease of maintenance ensures that users can keep their mower in optimal working condition with minimal effort.

Overall, the Craftsman 247.88853 stands out as a powerful, efficient, and user-friendly mowing solution, ideal for homeowners seeking to maintain their lawns with minimal hassle. With its combination of advanced features and reliable performance, it continues to be a favorite among lawn care enthusiasts.
Top Page Image Contents