Craftsman 247.88853 Final Adjustments, Auger Control, Traction Drive Clutch and Shift Lever

Page 11

Final Adjustments

Auger Control

To check the adjustment of the auger control, push forward the left hand clutch grip until the rubber bumper is compressed. There should be slack in the clutch cable.

Release the clutch grip. The cable should be straight. Make certain you can depress the auger control grip against the left handle completely.

If adjustment is necessary, loosen the hex jam nut and thread the cable in (for less slack) or out (for more slack).

Recheck the adjustment. Tighten the jam nut against the cable when correct adjustment is reached.

Traction Drive Clutch and Shift Lever

Tip the snow thrower forward so that it rests on the auger housing.

Move the shift lever all the way forward to the sixth (6) position.

With the traction drive lever released, spin the snow thrower wheels by hand. The wheels should turn; however, you may feel some resistance.

Engage the traction drive clutch grip. The wheels should no longer turn.

Now release the traction drive clutch grip, and spin the wheels again.

Move the shift lever back to the fast reverse position, then all the way forward again. There should be no resistance in the shift lever, and the wheels should turn.

If you face resistance when moving the shift lever or the snow thrower wheels stop when they should not, loosen the lock nut on the traction drive cable and unthread the cable one turn.

If the wheels can still be turned when you engage the traction drive clutch grip, loosen the lock nut on the traction drive cable and thread the cable in one turn.

Recheck the adjustment and repeat adjustment as necessary. Tighten the jam nut to secure the cable when correct adjustment is reached.

NOTE: If you are not sure that you have reached correct adjustment, refer to the Adjustment section on page 20.

Skid Shoe

The space between the shave plate and the ground can be adjusted. For close snow removal, place skid shoes in the low position. Use middle or high position when area to be cleared is uneven.

NOTE: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing an injury or damage to the snow thrower.

If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest position for maximum clearance between the ground and the shave plate.

Adjust skid shoes by loosening the four hex nuts and carriage bolts and moving skid shoes to desired position.

Make certain the entire bottom surface of skid shoe is against the ground to avoid uneven wear on the skid shoes.

Tighten nuts and bolts securely.

Skid Shoe

Loosen these hardware to adjust skid shoe

Figure 16

Tire Pressure (Pneumatic Tires)

The tires are over-inflated for shipping purposes. Check tire pressure and reduce to 15 to 20 psi.

NOTE: If the tire pressure is not equal in both tires, the unit may pull to one side or the other.

11

Image 11
Contents Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.A 247.888530Warranty Information Table of ContentsTraining Safe Operation PracticesMaintenance and Storage Hardware Pack Loose Parts AssemblyAttaching Handle Assembly Removing From CartonChute Hex Bolt Hex Flange Nut Keeper Attaching ChuteAttaching Chute Crank Lock Washer Hex Bolt Right Handle TabCable Guide Support Hex Bolt Upper Chute Crank BracketLower Chute Carriage Bolt Crank Bracket Hex Lock Nut Outer portion Fitting Cut-out Attaching Clutch CablesAttaching Shift Rod Attaching Turn TriggersSecure with screw Weld Nut Turn Lamp WiringTrigger Cable Handle Alternator Lamp Lead Wire Slot Skid Shoe Final AdjustmentsAuger Control Traction Drive Clutch and Shift LeverKnowing Your Snow Thrower Meets Ansi Safety StandardsOperation Before Starting Engine Operating ControlsStopping Snow Thrower Cold Start To Start EngineStarting Instructions At a Glance Electric StarterOperating Snow Thrower To Stop The Snow Thrower To Throw SnowOperating Tips Before StoppingCustomer Responsibilities MaintenanceClean snow thrower Clean skid shoes Clean shave plate General RecommendationsCheck Friction Wheel Engine MaintenanceLubrication Check V-beltsSpark Plug Viscosity ChartChecking Oil Level Changing OilAdjustments Service & AdjustmentsShave Plate And Skid Shoes ServiceCarburetor AugersHex Nut Lock Washer PushChanging Friction Wheel Rubber Drive BeltSprocket Spacer Hex Shaft Hex Hub CarburetorCarburetor Bowl Drain OFF-SEASON StoragePreparing Engine Preparing Snow ThrowerTrouble Possible Causes Corrective Action TROUBLE-SHOOTINGLabels MAP Repair Parts Sears Craftsman 9.0 H.P. Snow Thrower Model Polo Green Powder Black Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower 298 130B 301 396 340 300 264A 400 310 Key Part Description Qty Recoil Starter Carburetor Numero De Modelo Garantia DE InformaciónEspecificaciones Del Producto Entrenamiento Practicas Seguras DE OperacionMantenimiento Y Almacenamiento Piezas de Repuesto Conjunto DE Ferreteria DE FerreteriaHerramientas Requeridas EnsambladoExtraccion De La Unidad De La Caja Piezas SueltasFijacion De La Manivela De La Canaleta Fijacion De La CanaletaManija inferior de la canaleta ManijaCanaleta Superior Cable De la Fijacion De Los Cables Del Embrague Fijacion De La Vara De CambiosCableado de la Lámpara Fijacion De Los Gatillos De GiroAjuste de la Zapata Deslizante Ajustes FinalesAjuste del Control de la Hélice Ajuste del Control del Propulsor de TracciónControl de la helice Palanca De CambiosOperacion Conozca Su Expulsor De NieveArranque Del Motor Detencion Del Expulsor De NieveLlenado De Gasolina Y Aceite Arrancador eléctricoEnganche De La Propulsion Como Apagar El MotorPara Enganchar El Propulsor Enganche De Las Espirales Sin Fin Presion De La RuedasConsejos De Operacion Manejo De La Limpiadora De NieveLubricacion Mecanismo De CambiosMantenimiento Recomendaciones GeneralesMantenimiento del Motor Ajustes Service & AjustesCorreas de la espiral sin fin ServiceHelices Reemplazo De La CorreaNota Sea precavido para evitar apretar el cable de control Cubrierta del propulsor Correa propulsoraPinon Separador Eje hexagonal Cubo hexagonal del pinon Preparación del Expulsor de Nieve Almacenamiento DE Fuera DE TemporadaPreparación del motor Tabla DE Localizacion DE Fallas Problema Causas posible Accion correctoraYour Notes/Vuestro Apuntes Para pedir servicio de reparación a domicillio U.S.A. or Canada For in-home major brand repair serviceFor the repair or replacement parts you need To purchase or inquire about a Sears Maintenance Agreement

247.88853 specifications

The Craftsman 247.88853 is a renowned model in the realm of outdoor power equipment, particularly known for its robust design and high functionality. This versatile machine is primarily designed to provide users with an efficient lawn mowing experience while ensuring ease of use and maintenance.

One of the standout features of the Craftsman 247.88853 is its powerful engine. Equipped with a 24 HP V-twin gas engine, it delivers reliable performance for demanding mowing tasks. This powerful engine not only enhances cutting efficiency but also ensures that the mower can tackle tougher terrains with ease. Moreover, the engine operates smoothly, resulting in less vibration and noise, which makes for a more pleasant mowing experience.

The cutting system of the Craftsman 247.88853 is another significant characteristic that sets it apart. Featuring a 50-inch cutting deck, it provides a wide mowing path, significantly reducing the time spent on lawn maintenance. The deck is made of durable materials, ensuring longevity and resilience against the wear and tear of heavy use. Additionally, the height adjustment feature allows users to set the cutting height with precision, accommodating various grass types and desired lawn finishes.

In terms of user comfort and control, the Craftsman 247.88853 does not disappoint. It comes equipped with an ergonomic seat that provides ample support for long mowing sessions. Furthermore, the easy-to-use hydrostatic transmission enables smooth and effortless speed control, allowing users to navigate their lawns with agility.

The mower is designed with modern technologies that enhance its usability and efficiency. The inclusion of a built-in mulching capability is one such technology, which allows the grass to be finely chopped and returned to the lawn as natural fertilizer. This eco-friendly feature supports sustainability while promoting healthier lawn growth.

Lastly, maintenance and serviceability are made easier with the Craftsman 247.88853. The mower features a straightforward design that simplifies tasks such as oil changes, blade sharpening, and general upkeep. This focus on ease of maintenance ensures that users can keep their mower in optimal working condition with minimal effort.

Overall, the Craftsman 247.88853 stands out as a powerful, efficient, and user-friendly mowing solution, ideal for homeowners seeking to maintain their lawns with minimal hassle. With its combination of advanced features and reliable performance, it continues to be a favorite among lawn care enthusiasts.