Craftsman 247.88853 To Throw Snow, Operating Tips, Before Stopping, To Stop The Snow Thrower

Page 16

WARNING: To stop the auger, both levers must be released.

To Throw Snow

CAUTION: Check the area to be cleared for foreign objects. Remove, if any.

•Start the engine following Starting instructions.

•Rotate the discharge chute to the desired direction, away from bystanders and/or buildings. Move the chute distance control forward or backward to adjust the distance the snow is to be thrown.

•Select the speed according to snow condition.

CAUTION: Never move the shift lever without first releasing the drive clutch.

•Engage the auger control and traction drive control levers following instructions above.

•The interlock feature will allow you to remove your left hand from the auger control lever.

•When clearing the first pass through the snow, control the traction speed of the snow thrower according to the depth and condition of snow.

•To turn the unit left, squeeze left trigger; to turn right, squeeze right trigger.

•On each succeeding pass, readjust the chute deflector to the desired position and slightly overlap the previously cleared path.

•After the area is cleared, stop the snow thrower following instructions given below.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes as the engine will not develop full power until it reaches operating temperature.

Warning: The temperature of muffler and

surrounding areas may exceed 150o F. Avoid these areas.

•For most efficient snow removal, remove snow immediately after it falls.

•Discharge snow downwind whenever possible. Slightly overlap each previous swath.

•Set the skid shoes 1/4" below the scraper bar for normal usage. The skid shoes may be adjusted upward for hard-packed snow.

NOTE: It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing an injury or damage to the snow thrower.

•If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest position for maximum clearance between the ground and the shave plate.

•Clean the snow thrower thoroughly after each use.

Before Stopping

•Run engine for a few minutes to help dry off any moisture on engine.

•To avoid possible freeze-up of the starter, follow these steps:

Recoil Starter

a.With the engine running, pull the starter rope with a rapid, continuous full arm stroke three or four times.

Electric Starter

a.Connect power cord to switch box, then to 120 Volt AC receptacle.

b.While the engine is running, push the starter button and spin the starter for several seconds.

c.Disconnect power cord from the receptacle first, then from the snow thrower.

NOTE: The unusual sound from pulling the starter rope in the case of the recoil starter, or from spinning the starter in the case of the electric starter, will not harm the engine.

To Stop The Snow Thrower

•To stop the wheel, release the traction drive lever on the snow thrower.

•To stop throwing snow, release auger drive lever.

•To stop engine, push throttle control lever to OFF and pull out the key. Do not turn key.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 247.888530 Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.ATable of Contents Warranty InformationSafe Operation Practices TrainingMaintenance and Storage Hardware Pack Assembly Attaching Handle AssemblyRemoving From Carton Loose PartsAttaching Chute Attaching Chute CrankLock Washer Hex Bolt Right Handle Tab Chute Hex Bolt Hex Flange Nut KeeperLower Chute Carriage Bolt Crank Bracket Hex Lock Nut Support Hex Bolt Upper Chute Crank BracketCable Guide Attaching Clutch Cables Attaching Shift RodAttaching Turn Triggers Outer portion Fitting Cut-outTrigger Cable Handle Alternator Lamp Lead Wire Slot Lamp WiringSecure with screw Weld Nut Turn Final Adjustments Auger ControlTraction Drive Clutch and Shift Lever Skid ShoeOperation Meets Ansi Safety StandardsKnowing Your Snow Thrower Stopping Snow Thrower Operating ControlsBefore Starting Engine To Start Engine Starting Instructions At a GlanceElectric Starter Cold StartOperating Snow Thrower To Throw Snow Operating TipsBefore Stopping To Stop The Snow ThrowerMaintenance Clean snow thrower Clean skid shoes Clean shave plateGeneral Recommendations Customer ResponsibilitiesEngine Maintenance LubricationCheck V-belts Check Friction WheelViscosity Chart Checking Oil LevelChanging Oil Spark PlugService & Adjustments AdjustmentsService CarburetorAugers Shave Plate And Skid ShoesPush Hex Nut Lock WasherDrive Belt Changing Friction Wheel RubberCarburetor Sprocket Spacer Hex Shaft Hex HubOFF-SEASON Storage Preparing EnginePreparing Snow Thrower Carburetor Bowl DrainTROUBLE-SHOOTING Trouble Possible Causes Corrective ActionLabels MAP Repair Parts Sears Craftsman 9.0 H.P. Snow Thrower Model Polo Green Powder Black Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower 298 130B 301 396 340 300 264A 400 310 Key Part Description Qty Recoil Starter Carburetor Especificaciones Del Producto Garantia DE InformaciónNumero De Modelo Practicas Seguras DE Operacion EntrenamientoMantenimiento Y Almacenamiento Conjunto DE Ferreteria DE Ferreteria Piezas de RepuestoEnsamblado Extraccion De La Unidad De La CajaPiezas Sueltas Herramientas RequeridasFijacion De La Canaleta Fijacion De La Manivela De La CanaletaCanaleta Superior Cable De la ManijaManija inferior de la canaleta Fijacion De La Vara De Cambios Fijacion De Los Cables Del EmbragueFijacion De Los Gatillos De Giro Cableado de la LámparaAjustes Finales Ajuste del Control de la HéliceAjuste del Control del Propulsor de Tracción Ajuste de la Zapata DeslizantePalanca De Cambios OperacionConozca Su Expulsor De Nieve Control de la heliceDetencion Del Expulsor De Nieve Llenado De Gasolina Y AceiteArrancador eléctrico Arranque Del MotorPara Enganchar El Propulsor Como Apagar El MotorEnganche De La Propulsion Presion De La Ruedas Consejos De OperacionManejo De La Limpiadora De Nieve Enganche De Las Espirales Sin FinMecanismo De Cambios MantenimientoRecomendaciones Generales LubricacionMantenimiento del Motor Service & Ajustes AjustesService HelicesReemplazo De La Correa Correas de la espiral sin finNota Sea precavido para evitar apretar el cable de control Correa propulsora Cubrierta del propulsorPinon Separador Eje hexagonal Cubo hexagonal del pinon Preparación del motor Almacenamiento DE Fuera DE TemporadaPreparación del Expulsor de Nieve Problema Causas posible Accion correctora Tabla DE Localizacion DE FallasYour Notes/Vuestro Apuntes U.S.A. or Canada For in-home major brand repair service For the repair or replacement parts you needTo purchase or inquire about a Sears Maintenance Agreement Para pedir servicio de reparación a domicillio

247.88853 specifications

The Craftsman 247.88853 is a renowned model in the realm of outdoor power equipment, particularly known for its robust design and high functionality. This versatile machine is primarily designed to provide users with an efficient lawn mowing experience while ensuring ease of use and maintenance.

One of the standout features of the Craftsman 247.88853 is its powerful engine. Equipped with a 24 HP V-twin gas engine, it delivers reliable performance for demanding mowing tasks. This powerful engine not only enhances cutting efficiency but also ensures that the mower can tackle tougher terrains with ease. Moreover, the engine operates smoothly, resulting in less vibration and noise, which makes for a more pleasant mowing experience.

The cutting system of the Craftsman 247.88853 is another significant characteristic that sets it apart. Featuring a 50-inch cutting deck, it provides a wide mowing path, significantly reducing the time spent on lawn maintenance. The deck is made of durable materials, ensuring longevity and resilience against the wear and tear of heavy use. Additionally, the height adjustment feature allows users to set the cutting height with precision, accommodating various grass types and desired lawn finishes.

In terms of user comfort and control, the Craftsman 247.88853 does not disappoint. It comes equipped with an ergonomic seat that provides ample support for long mowing sessions. Furthermore, the easy-to-use hydrostatic transmission enables smooth and effortless speed control, allowing users to navigate their lawns with agility.

The mower is designed with modern technologies that enhance its usability and efficiency. The inclusion of a built-in mulching capability is one such technology, which allows the grass to be finely chopped and returned to the lawn as natural fertilizer. This eco-friendly feature supports sustainability while promoting healthier lawn growth.

Lastly, maintenance and serviceability are made easier with the Craftsman 247.88853. The mower features a straightforward design that simplifies tasks such as oil changes, blade sharpening, and general upkeep. This focus on ease of maintenance ensures that users can keep their mower in optimal working condition with minimal effort.

Overall, the Craftsman 247.88853 stands out as a powerful, efficient, and user-friendly mowing solution, ideal for homeowners seeking to maintain their lawns with minimal hassle. With its combination of advanced features and reliable performance, it continues to be a favorite among lawn care enthusiasts.
Top Page Image Contents