Craftsman 247.88853 owner manual Service, Carburetor, Augers, Shave Plate And Skid Shoes

Page 21

Carburetor

WARNING: If any adjustments are made to the engine while the engine is running (e.g. carburetor), keep clear of all moving parts. Be careful of heated surfaces and mufflers.

Minor carburetor adjustments may be required to compensate for differences in fuel temperature, altitude and load.

Service

Augers

The augers are secured to the spiral shaft with two shear bolts and hex lock nuts. See Figure 23. If you hit a foreign object or ice jam, the snow thrower is designed so that the bolts will shear. This type of nut is used where vibration occurs.

If the augers do not turn, check to see if the bolts have sheared. Two replacement shear bolts (shown in Figure 23 inset ) and hex lock nuts have been provided with the snow thrower. Since lock nuts cannot be threaded onto a bolt by hand, use a wrench. When replacing bolts, spray an oil lubricant into shaft before inserting new bolts.

Shear Bolt

Shear Bolt

Shave Plate

Figure 23

Shave Plate And Skid Shoes

The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary.

•Remove the four carriage bolts, belleville washers and hex nuts which attach skid shoes to the snow thrower on two sides. See Figure 23.

•Reassemble new skid shoes with the four carriage bolts, belleville washers (cupped side goes against skid shoes) and hex nuts. Make certain the skid shoes are adjusted to be level.

•To remove shave plate, remove the skid shoe and the rest of hardware including carriage

bolts, belleville washers and hex nuts which attach shave plate to the snow thrower housing. For location of shave plate, see Figure 23.

•Reassemble new shave plate, making sure heads of the carriage bolts are to the inside of the housing. Reinstall skid shoe. Tighten securely.

Replacing Belt

WARNING: Disconnect the spark plug wire from the spark plug and ground.

Auger Belts

•Remove the plastic belt cover on the front of the engine by removing the two self-tapping screws. See Figure 24.

Self-Tapping Screw

Belt Cover

Self-Tapping Screw

Figure 24

•Disconnect chute crank assembly at the discharge chute by removing the hairpin clip and the two flat washers. See Figure 25.

Chute

Hairpin Clip

Crank

 

 

Flat

Washer

Figure 25

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.A 247.888530Warranty Information Table of ContentsTraining Safe Operation PracticesMaintenance and Storage Hardware Pack Attaching Handle Assembly AssemblyRemoving From Carton Loose PartsAttaching Chute Crank Attaching ChuteLock Washer Hex Bolt Right Handle Tab Chute Hex Bolt Hex Flange Nut KeeperSupport Hex Bolt Upper Chute Crank Bracket Lower Chute Carriage Bolt Crank Bracket Hex Lock NutCable Guide Attaching Shift Rod Attaching Clutch CablesAttaching Turn Triggers Outer portion Fitting Cut-outLamp Wiring Trigger Cable Handle Alternator Lamp Lead Wire SlotSecure with screw Weld Nut Turn Auger Control Final AdjustmentsTraction Drive Clutch and Shift Lever Skid ShoeMeets Ansi Safety Standards OperationKnowing Your Snow Thrower Operating Controls Stopping Snow ThrowerBefore Starting Engine Starting Instructions At a Glance To Start EngineElectric Starter Cold StartOperating Snow Thrower Operating Tips To Throw SnowBefore Stopping To Stop The Snow ThrowerClean snow thrower Clean skid shoes Clean shave plate MaintenanceGeneral Recommendations Customer ResponsibilitiesLubrication Engine MaintenanceCheck V-belts Check Friction WheelChecking Oil Level Viscosity ChartChanging Oil Spark PlugAdjustments Service & AdjustmentsCarburetor ServiceAugers Shave Plate And Skid ShoesHex Nut Lock Washer PushChanging Friction Wheel Rubber Drive BeltSprocket Spacer Hex Shaft Hex Hub CarburetorPreparing Engine OFF-SEASON StoragePreparing Snow Thrower Carburetor Bowl DrainTrouble Possible Causes Corrective Action TROUBLE-SHOOTINGLabels MAP Repair Parts Sears Craftsman 9.0 H.P. Snow Thrower Model Polo Green Powder Black Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower 298 130B 301 396 340 300 264A 400 310 Key Part Description Qty Recoil Starter Carburetor Garantia DE Información Especificaciones Del ProductoNumero De Modelo Entrenamiento Practicas Seguras DE OperacionMantenimiento Y Almacenamiento Piezas de Repuesto Conjunto DE Ferreteria DE FerreteriaExtraccion De La Unidad De La Caja EnsambladoPiezas Sueltas Herramientas RequeridasFijacion De La Manivela De La Canaleta Fijacion De La CanaletaManija Canaleta Superior Cable De laManija inferior de la canaleta Fijacion De Los Cables Del Embrague Fijacion De La Vara De CambiosCableado de la Lámpara Fijacion De Los Gatillos De GiroAjuste del Control de la Hélice Ajustes FinalesAjuste del Control del Propulsor de Tracción Ajuste de la Zapata DeslizanteOperacion Palanca De CambiosConozca Su Expulsor De Nieve Control de la heliceLlenado De Gasolina Y Aceite Detencion Del Expulsor De NieveArrancador eléctrico Arranque Del MotorComo Apagar El Motor Para Enganchar El PropulsorEnganche De La Propulsion Consejos De Operacion Presion De La RuedasManejo De La Limpiadora De Nieve Enganche De Las Espirales Sin FinMantenimiento Mecanismo De CambiosRecomendaciones Generales LubricacionMantenimiento del Motor Ajustes Service & AjustesHelices ServiceReemplazo De La Correa Correas de la espiral sin finNota Sea precavido para evitar apretar el cable de control Cubrierta del propulsor Correa propulsoraPinon Separador Eje hexagonal Cubo hexagonal del pinon Almacenamiento DE Fuera DE Temporada Preparación del motorPreparación del Expulsor de Nieve Tabla DE Localizacion DE Fallas Problema Causas posible Accion correctoraYour Notes/Vuestro Apuntes For the repair or replacement parts you need U.S.A. or Canada For in-home major brand repair serviceTo purchase or inquire about a Sears Maintenance Agreement Para pedir servicio de reparación a domicillio

247.88853 specifications

The Craftsman 247.88853 is a renowned model in the realm of outdoor power equipment, particularly known for its robust design and high functionality. This versatile machine is primarily designed to provide users with an efficient lawn mowing experience while ensuring ease of use and maintenance.

One of the standout features of the Craftsman 247.88853 is its powerful engine. Equipped with a 24 HP V-twin gas engine, it delivers reliable performance for demanding mowing tasks. This powerful engine not only enhances cutting efficiency but also ensures that the mower can tackle tougher terrains with ease. Moreover, the engine operates smoothly, resulting in less vibration and noise, which makes for a more pleasant mowing experience.

The cutting system of the Craftsman 247.88853 is another significant characteristic that sets it apart. Featuring a 50-inch cutting deck, it provides a wide mowing path, significantly reducing the time spent on lawn maintenance. The deck is made of durable materials, ensuring longevity and resilience against the wear and tear of heavy use. Additionally, the height adjustment feature allows users to set the cutting height with precision, accommodating various grass types and desired lawn finishes.

In terms of user comfort and control, the Craftsman 247.88853 does not disappoint. It comes equipped with an ergonomic seat that provides ample support for long mowing sessions. Furthermore, the easy-to-use hydrostatic transmission enables smooth and effortless speed control, allowing users to navigate their lawns with agility.

The mower is designed with modern technologies that enhance its usability and efficiency. The inclusion of a built-in mulching capability is one such technology, which allows the grass to be finely chopped and returned to the lawn as natural fertilizer. This eco-friendly feature supports sustainability while promoting healthier lawn growth.

Lastly, maintenance and serviceability are made easier with the Craftsman 247.88853. The mower features a straightforward design that simplifies tasks such as oil changes, blade sharpening, and general upkeep. This focus on ease of maintenance ensures that users can keep their mower in optimal working condition with minimal effort.

Overall, the Craftsman 247.88853 stands out as a powerful, efficient, and user-friendly mowing solution, ideal for homeowners seeking to maintain their lawns with minimal hassle. With its combination of advanced features and reliable performance, it continues to be a favorite among lawn care enthusiasts.
Top Page Image Contents