Craftsman 247.88853 owner manual Safe Operation Practices, Training

Page 3

SAFE OPERATION PRACTICES

This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your snow thrower. Failure to comply with these instructions may result in personal injury. When you see this symbol—heed its warning.

Your snow thrower was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the

DANGER:operator can result in serious injury. If you violate any of these rules, you may cause serious injury to yourself or others.

This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.

In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest Sears Authorized Service Center (See the REPAIR PARTS section of this manual.)

The engine exhaust from this product contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.

TRAINING

Read this owner’s guide carefully in its entirety before attempting to assemble or operate this machine. Be completely familiar with the controls and the proper use of this machine before operating it. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

Never allow children under 14 years old to operate a snow thrower. Children 14 years old and over should only operate a snow thrower under close parental supervision. Only persons well acquainted with these rules of safe operation should be allowed to use your snow thrower.

No one should operate this unit while intoxicated or while taking medication that impairs the senses or reactions.

Keep the area of operation clear of all persons, especially small children and pets.

Exercise caution to avoid slipping or falling, especially when operating in reverse.

PREPARATION

Thoroughly inspect the area where the equipment is to be used and remove all door mats, sleds, boards, wires and other foreign objects.

Do not operate equipment without wearing adequate outer garments for winter. Do not wear jewelry, long scarfs or other loose clothing which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.

Before working with gasoline, extinguish all cigarettes and other sources of ignition. Check the fuel before starting the engine. Gasoline is an extremely flammable fuel. Do not fill the gasoline tank indoors, while the engine is running, or until engine has been allowed to cool at least two minutes. Replace

gasoline cap securely and wipe off any spilled gasoline before starting the engine as it may cause a fire or explosion.

Use a grounded three wire plug-in for all units with electric drive motors or electric starting motors.

Adjust collector housing height to clear gravel or crushed rock surface.

Never attempt to make any adjustments while engine is running (except where specifically recommended by manufacturer).

Let engine and machine adjust to outdoor temperature before starting to clear snow.

Always wear safety glasses or eye shields during operation or while performing an adjustment or repair, to protect eyes from foreign objects that may be thrown from the machine in any direction.

OPERATION

Do not put hands or feet near or under rotating parts. Keep clear of discharge opening and auger at all times.

Exercise extreme caution when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

Do not carry passengers.

After striking a foreign object, stop the engine, remove wire from the spark plug and thoroughly inspect the snow thrower for any damage. Repair the damage before restarting and operating the snow thrower.

If the snow thrower starts to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble.

Stop the engine whenever you leave the operating position, before unclogging the collector/impeller housing or discharge guide and before making any repairs, adjustments, or inspections. Never place your

3

Image 3
Contents Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.A 247.888530Warranty Information Table of ContentsTraining Safe Operation PracticesMaintenance and Storage Hardware Pack Loose Parts AssemblyAttaching Handle Assembly Removing From CartonChute Hex Bolt Hex Flange Nut Keeper Attaching ChuteAttaching Chute Crank Lock Washer Hex Bolt Right Handle TabSupport Hex Bolt Upper Chute Crank Bracket Lower Chute Carriage Bolt Crank Bracket Hex Lock NutCable Guide Outer portion Fitting Cut-out Attaching Clutch CablesAttaching Shift Rod Attaching Turn TriggersLamp Wiring Trigger Cable Handle Alternator Lamp Lead Wire SlotSecure with screw Weld Nut Turn Skid Shoe Final AdjustmentsAuger Control Traction Drive Clutch and Shift LeverMeets Ansi Safety Standards OperationKnowing Your Snow Thrower Operating Controls Stopping Snow ThrowerBefore Starting Engine Cold Start To Start EngineStarting Instructions At a Glance Electric StarterOperating Snow Thrower To Stop The Snow Thrower To Throw SnowOperating Tips Before StoppingCustomer Responsibilities MaintenanceClean snow thrower Clean skid shoes Clean shave plate General RecommendationsCheck Friction Wheel Engine MaintenanceLubrication Check V-beltsSpark Plug Viscosity ChartChecking Oil Level Changing OilAdjustments Service & AdjustmentsShave Plate And Skid Shoes ServiceCarburetor AugersHex Nut Lock Washer PushChanging Friction Wheel Rubber Drive BeltSprocket Spacer Hex Shaft Hex Hub CarburetorCarburetor Bowl Drain OFF-SEASON StoragePreparing Engine Preparing Snow ThrowerTrouble Possible Causes Corrective Action TROUBLE-SHOOTINGLabels MAP Repair Parts Sears Craftsman 9.0 H.P. Snow Thrower Model Polo Green Powder Black Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower Model Sears Craftsman 9.0 H.P. Snow Thrower 298 130B 301 396 340 300 264A 400 310 Key Part Description Qty Recoil Starter Carburetor Garantia DE Información Especificaciones Del ProductoNumero De Modelo Entrenamiento Practicas Seguras DE OperacionMantenimiento Y Almacenamiento Piezas de Repuesto Conjunto DE Ferreteria DE FerreteriaHerramientas Requeridas EnsambladoExtraccion De La Unidad De La Caja Piezas SueltasFijacion De La Manivela De La Canaleta Fijacion De La CanaletaManija Canaleta Superior Cable De laManija inferior de la canaleta Fijacion De Los Cables Del Embrague Fijacion De La Vara De CambiosCableado de la Lámpara Fijacion De Los Gatillos De GiroAjuste de la Zapata Deslizante Ajustes FinalesAjuste del Control de la Hélice Ajuste del Control del Propulsor de TracciónControl de la helice Palanca De CambiosOperacion Conozca Su Expulsor De NieveArranque Del Motor Detencion Del Expulsor De NieveLlenado De Gasolina Y Aceite Arrancador eléctricoComo Apagar El Motor Para Enganchar El PropulsorEnganche De La Propulsion Enganche De Las Espirales Sin Fin Presion De La RuedasConsejos De Operacion Manejo De La Limpiadora De NieveLubricacion Mecanismo De CambiosMantenimiento Recomendaciones GeneralesMantenimiento del Motor Ajustes Service & AjustesCorreas de la espiral sin fin ServiceHelices Reemplazo De La CorreaNota Sea precavido para evitar apretar el cable de control Cubrierta del propulsor Correa propulsoraPinon Separador Eje hexagonal Cubo hexagonal del pinon Almacenamiento DE Fuera DE Temporada Preparación del motorPreparación del Expulsor de Nieve Tabla DE Localizacion DE Fallas Problema Causas posible Accion correctoraYour Notes/Vuestro Apuntes Para pedir servicio de reparación a domicillio U.S.A. or Canada For in-home major brand repair serviceFor the repair or replacement parts you need To purchase or inquire about a Sears Maintenance Agreement

247.88853 specifications

The Craftsman 247.88853 is a renowned model in the realm of outdoor power equipment, particularly known for its robust design and high functionality. This versatile machine is primarily designed to provide users with an efficient lawn mowing experience while ensuring ease of use and maintenance.

One of the standout features of the Craftsman 247.88853 is its powerful engine. Equipped with a 24 HP V-twin gas engine, it delivers reliable performance for demanding mowing tasks. This powerful engine not only enhances cutting efficiency but also ensures that the mower can tackle tougher terrains with ease. Moreover, the engine operates smoothly, resulting in less vibration and noise, which makes for a more pleasant mowing experience.

The cutting system of the Craftsman 247.88853 is another significant characteristic that sets it apart. Featuring a 50-inch cutting deck, it provides a wide mowing path, significantly reducing the time spent on lawn maintenance. The deck is made of durable materials, ensuring longevity and resilience against the wear and tear of heavy use. Additionally, the height adjustment feature allows users to set the cutting height with precision, accommodating various grass types and desired lawn finishes.

In terms of user comfort and control, the Craftsman 247.88853 does not disappoint. It comes equipped with an ergonomic seat that provides ample support for long mowing sessions. Furthermore, the easy-to-use hydrostatic transmission enables smooth and effortless speed control, allowing users to navigate their lawns with agility.

The mower is designed with modern technologies that enhance its usability and efficiency. The inclusion of a built-in mulching capability is one such technology, which allows the grass to be finely chopped and returned to the lawn as natural fertilizer. This eco-friendly feature supports sustainability while promoting healthier lawn growth.

Lastly, maintenance and serviceability are made easier with the Craftsman 247.88853. The mower features a straightforward design that simplifies tasks such as oil changes, blade sharpening, and general upkeep. This focus on ease of maintenance ensures that users can keep their mower in optimal working condition with minimal effort.

Overall, the Craftsman 247.88853 stands out as a powerful, efficient, and user-friendly mowing solution, ideal for homeowners seeking to maintain their lawns with minimal hassle. With its combination of advanced features and reliable performance, it continues to be a favorite among lawn care enthusiasts.