Craftsman 247.88851 Before Starting Engine, To Start Engine, Electric Starter, Cold Start

Page 14

Before Starting Engine

Fill Gas

WARNING: Gasoline is flammable and cau- tion must be used when handling or storing it.

Do not fillfuel tank while the snow thrower is running, when it is hot or when it is in an enclosed area.

Keep your snow thrower away from any open flame or an electrical spark and do not smoke while filling the fuel tank.

Never fill the fuel tank completely. Fill the tank to within 1/4"-1/2" from the top to provide space for expansion of fuel.

Always fill the fuel tank outdoors and use a funnel or spout to prevent spilling.

Make sure to wipe off any spilled fuel before starting the engine.

•Store gasoline in a clean, approved container and keep the cap in place on the container.

•Make sure that the container from which you pour the gasoline is clean and free from rust or other foreign particles.

•Fill fuel tank with clean, fresh, unleaded grade automotive gasoline.

•At the end of the job, empty the fuel tank if the snow thrower is not going to be used for 30 days

or longer. See storage instructions on of this manual.

CAUTION: Experience indicates that alcohol

blended fuels (called gasohol) or those using etha- nol or methanol can attract moisture which leads to

separation and formation of acids during storage.

Acidic gas can damage the fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next sea- son. See storage Instructions for additional information.

Starting Instructions at a glance_

Snow

Spark

Drive

Throttle

Ignition

Choke

Thrower

Plug

Levers

control

Key

 

 

wire

 

 

 

 

Electric

Connect

Release

Move to

Push to

Move to

Starter

 

 

FAST

snap in

FULL

Recoil

Connect

Release

Move to

Push to

Move to

Starter

 

 

FAST

snap in

FULL

Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

To Start Engine

A WARNING: Be sure no one other than the operator is standing near the snow

thrower while starting or operating. Do not operate this snow thrower unless the

discharge chute assembly has been properly installed and is secured.

A, Electric Starter

throttle

_'_

Pull

-

starter

Figure 19

For location of all the engine controls referred to in this section, see Figure 19.

Before starting, make sure that the engine has suffi- cient oil. The snow thrower engine is equipped with a 120 volt A.C. electric starter and recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 volt AC household current. Follow all instructions carefully

Cold Start

NOTE: If the unit shows any sign of motion (drive or augers) with the clutch grips disengaged, shut the engine off immediately. Readjust as instructed in the

Power

Primer

Starter

After starting

Cord

 

 

 

 

Connect

--

Push

1.

Release button

to source

 

button

2.

Move Choke to Off

 

 

 

3.

Disconnect cord

--

Prime

Pull

1.

Release handle

 

 

handle

2.

Move Choke to Off,

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Craftsman Content Two -Year Warranty on Craftsman Snow ThrowerTraining KWARNING LHI Loose Parts Attaching Handle AssemblyRemoving From Carton Tools RequiredAttaching Chute Crank Bolt HexLower Chute Carriage Bolt Crank Bracket Hex Lock Nut Underthisfor i HandlePanel JChute Crank Bracket Cotter PinAttaching Turn Triggers Attaching Clutch CablesAttaching Shift Rod FerruleLamp Wiring Final AdjustmentsMake sure that the spark plug is disconnected Adjusting Traction Drive ControlAdjusting Skid Shoe Hex NutChute Crank Meets Ansi Safety StandardsKnowing Your Snow Thrower Discharge ChuteOperating Controls Electric Starter Before Starting EngineTo Start Engine Cold StartRecoil Starter Operating Snow ThrowerWarm Start Frozen Recoil StarterBefore Stopping To Throw SnowOperating Tips To Engage AugersGeneral Recommendations Customer ResponsibilitiesCheck V-belts Engine MaintenanceLubrication Changing Oil ChartChecking Oil Level Spark PlugAuger Clutch AdjustmentsAugers Shift RodSelf-Tapping Shave Plate And Skid ShoesAuger Drive Belts Bell Washer Hex Bolt Drive BeltFriction Wheel Rubber Carburetor Engine OilPreparing Snow Thrower Bowl DrainPossible Cause Sears Craftsman 9.0 H.P. Snow Thrower Model Qty Sears Craftsman 9.0 H.P. Snow Thrower Model Actuator Sears Craftsman 9.0 H.P. Snow Thrower Model Key Pad No PaR No Description Qty Sears Craftsman 9.0 H.P, Snow Thrower Model Key Pa No Flat Idler ScrewCarburetor 315 305100 224 219//1 3t0GMCR Flywheel Nut220 35438 Choke Knob Recoil Starter 8OO-4-REPAIR

247.88851 specifications

The Craftsman 247.88851 is a standout lawn mower, designed to meet the needs of homeowners looking for a reliable and efficient gardening solution. This model combines innovative features with user-friendly technology to provide an exceptional mowing experience. Its power and performance are backed by a robust 21-inch cutting deck, making it ideal for tackling small to medium-sized yards with precision.

One of the notable features of the Craftsman 247.88851 is its 140cc engine. This engine offers sufficient power to handle various grass types and conditions, ensuring a clean and even cut every time. The starting mechanism boasts a reliable pull-start system, simplifying the operation and enhancing user convenience. This model also incorporates a 5-position height adjustment feature, allowing users to customize their mowing height according to their lawn's specific needs.

The Craftsman 247.88851 stands out with its ease of maneuverability. Its lightweight design and compact frame facilitate effortless navigation around obstacles such as trees and garden beds. The lawn mower is equipped with 7-inch front wheels and 8-inch rear wheels, providing excellent stability and traction. This stability is crucial for achieving optimal mowing results, especially on uneven terrain.

Another remarkable technology featured in the Craftsman 247.88851 is its superior grass collection system. The mower comes with a 1.9-bushel grass bag that efficiently collects clippings, ensuring a tidy lawn finish. Alternatively, users can opt for mulching functionality, which finely cuts and distributes the clippings back into the lawn, promoting healthy growth and providing essential nutrients.

In terms of build quality, the Craftsman 247.88851 is constructed with durable materials that withstand the rigors of regular use. Its sturdy design minimizes vibrations, resulting in a smoother mowing experience while reducing operator fatigue.

Overall, the Craftsman 247.88851 is an excellent choice for homeowners seeking a powerful, efficient, and easy-to-use lawn mower. Its combination of a strong engine, precise cutting capabilities, and advanced features makes it a valuable addition to any garden maintenance toolkit. Whether tackling overgrown patches or maintaining a well-groomed lawn, this mower delivers consistent and reliable performance.
Top Page Image Contents