Craftsman 247.88851 owner manual Operating Controls

Page 13

Operating Controls

(See Figure 17.)

Chute Crank

The chute crank is located on the left hand side of the snow thrower. To change the direction in which snow is thrown, turn chute crank as follows:

turn clockwise to discharge to the left;

turn counterclockwise to discharge to the right.

Throttle Control

The throttle control is located on the engine. It regulates the speed of the engine.

Safety Ignition Switch

The ignition key must be inserted into the switch for the unit to start. Remove the ignition key when the snow thrower is not in use.

Left And Right Turn Trigger

The leftand right turn triggers are located on the underside of the handles and are used to assist in

steering your snow thrower. Squeeze the right turn trigger when turning right, squeeze the left turn trigger when turning left. Operate your snow thrower in open areas until you become familiar with these controls.

Shift Lever

The shift lever is located in the center of the handle panel. It may be moved into one of eight positions:

a.Forward--oneof six speeds; positionone (1) is the slowest and position six (6) is the fastest.

b.Reverse--tworeverse (R) speeds; R2 is faster.

Use the shift lever to determine ground speed. Do not shift to different speed while the unit is moving.

Auger Control

The auger controlis located on the left handle. Squeeze the auger controlagainst the handle to engage the augers; release to disengage the augers. (Traction drive controlmust also be released.)

Traction Drive Control

The traction drive control is located on the right

handle. Squeeze the traction drive control to engage the track drive; release to stop.

This same lever also locks the auger control so that you can turn the chute crank without interrupting the snow throwing process. If the auger control is engaged with the traction drive controlengaged, you can release the auger control(on the left handle) and the augers will remain engaged. Release the traction drive controlto stop both the augers and the track drive. (Auger controlmust also be released).

Chute Distance Control

The distance that snow is thrown can be adjusted by

adjusting the angle of the chute assembly. Move the chute distance control forward to decrease the

distance, toward the rear to increase the distance.

Weight Transfer Lever

The weight transfer lever is located on the right side of the snow thrower and is used to select the position of the housing and the method of track operation. See Figure 18. Move the lever to the right, then forward or backward to one of the three positions.

Normal

Snow

Position

iPacked

p%nOtiWon ._ans portPosition

Figure 18

a.Transport_Raises the front end of the snow thrower for easy transport. Using proper caution, this position may also be used on many gravel driveways to clear snow while leaving gravel undisturbed.

b.Normal Snow--Allows the tracks to be suspended independently for continuous ground contact.

c.Packed Snovv--Locksthe front end of the snow thrower down to the ground for hard- packed or icy snow conditions.

To Stop The Snow Thrower

To stop the track, release the traction drive lever of the snow thrower.

To stop throwingsnow, releas_the auger drive lever and the drive lever if engaged.

To stop the engine, push the throttle control lever to OFF and pull out the ignition key. Do not turn key.

13

Image 13
Contents Craftsman Two -Year Warranty on Craftsman Snow Thrower ContentTraining KWARNING LHI Removing From Carton Attaching Handle AssemblyLoose Parts Tools RequiredBolt Hex Attaching Chute CrankChute Crank Bracket Underthisfor i HandlePanel JLower Chute Carriage Bolt Crank Bracket Hex Lock Nut Cotter PinAttaching Shift Rod Attaching Clutch CablesAttaching Turn Triggers FerruleFinal Adjustments Lamp WiringAdjusting Skid Shoe Adjusting Traction Drive ControlMake sure that the spark plug is disconnected Hex NutKnowing Your Snow Thrower Meets Ansi Safety StandardsChute Crank Discharge ChuteOperating Controls To Start Engine Before Starting EngineElectric Starter Cold StartWarm Start Operating Snow ThrowerRecoil Starter Frozen Recoil StarterOperating Tips To Throw SnowBefore Stopping To Engage AugersCustomer Responsibilities General RecommendationsLubrication Engine MaintenanceCheck V-belts Checking Oil Level ChartChanging Oil Spark PlugAugers AdjustmentsAuger Clutch Shift RodAuger Drive Belts Shave Plate And Skid ShoesSelf-Tapping Friction Wheel Rubber Drive BeltBell Washer Hex Bolt Engine Oil CarburetorBowl Drain Preparing Snow ThrowerPossible Cause Sears Craftsman 9.0 H.P. Snow Thrower Model Qty Sears Craftsman 9.0 H.P. Snow Thrower Model Actuator Sears Craftsman 9.0 H.P. Snow Thrower Model Key Pad No PaR No Description Qty Sears Craftsman 9.0 H.P, Snow Thrower Model Key Pa No Screw Flat IdlerCarburetor 100 224 305315 219//1 3t0GFlywheel Nut MCR220 35438 Choke Knob Recoil Starter 8OO-4-REPAIR

247.88851 specifications

The Craftsman 247.88851 is a standout lawn mower, designed to meet the needs of homeowners looking for a reliable and efficient gardening solution. This model combines innovative features with user-friendly technology to provide an exceptional mowing experience. Its power and performance are backed by a robust 21-inch cutting deck, making it ideal for tackling small to medium-sized yards with precision.

One of the notable features of the Craftsman 247.88851 is its 140cc engine. This engine offers sufficient power to handle various grass types and conditions, ensuring a clean and even cut every time. The starting mechanism boasts a reliable pull-start system, simplifying the operation and enhancing user convenience. This model also incorporates a 5-position height adjustment feature, allowing users to customize their mowing height according to their lawn's specific needs.

The Craftsman 247.88851 stands out with its ease of maneuverability. Its lightweight design and compact frame facilitate effortless navigation around obstacles such as trees and garden beds. The lawn mower is equipped with 7-inch front wheels and 8-inch rear wheels, providing excellent stability and traction. This stability is crucial for achieving optimal mowing results, especially on uneven terrain.

Another remarkable technology featured in the Craftsman 247.88851 is its superior grass collection system. The mower comes with a 1.9-bushel grass bag that efficiently collects clippings, ensuring a tidy lawn finish. Alternatively, users can opt for mulching functionality, which finely cuts and distributes the clippings back into the lawn, promoting healthy growth and providing essential nutrients.

In terms of build quality, the Craftsman 247.88851 is constructed with durable materials that withstand the rigors of regular use. Its sturdy design minimizes vibrations, resulting in a smoother mowing experience while reducing operator fatigue.

Overall, the Craftsman 247.88851 is an excellent choice for homeowners seeking a powerful, efficient, and easy-to-use lawn mower. Its combination of a strong engine, precise cutting capabilities, and advanced features makes it a valuable addition to any garden maintenance toolkit. Whether tackling overgrown patches or maintaining a well-groomed lawn, this mower delivers consistent and reliable performance.