Craftsman 247.88851 owner manual Preparing Snow Thrower, Bowl Drain

Page 24

ifyoursnowthrowerisleftunusedfor30daysor

longer,itneedstobepreparedforstorageAlso,at.

theendofthesnowseason,youshouldfollowthe samesetofinstructionsandstorethesnowthrower

properlyfortheoff-seasonProperstorageensures. longerlifeofthesnowthrower.

Preparing Engine

WARNING: Never store snow thrower with fuel in tank indoors or in poorly ventilated areas, where fuel fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance.

It is important to prevent gum deposits from forming in essential fuel system parts of the engine such as the carburetor, fuel filter, fuel hose or tank during storage.

Also experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

To avoid engine problems, the fuel system shouldbe emptiedbefore storage for 30 days or longer. Follow these instructions to prepare your snow thrower for storage:

•Remove all gasoline from the carburetor and the fuel tank to prevent gum deposits from forming on these parts and causing possible malfunction of the engine.

Bowl Drain

Figure 31

WARNING: Drain fuel into approved container outdoors, away from any open flame. Be certain engine is cool. Do not smoke.

Fuel left in engine during warm weather deteriorates and will cause serious starting problems,

Run the engine until the fuel tank is empty and it stops due to lack of fuel.

Drain carburetor by pressing upward on bowl drain, located below the carburetor cover. See Figure 31.

&WARNING: Do not drain carburetor if using fuel stabilizer. Never use engine or

carburetor cleaning products in the fuel tank or permanent damage may occur.

NOTE: Fuel stabilizer (such as STA-BIL) is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to

gasoline in fuel tank or storage container. Always follow mix ratio found on stabilizer container. Run

engine at least 10 minutes after adding stabilizer to allow it to reach the carburetor. Do not drain

carburetor if using fuel stabilizer.

•Remove the spark plug and pour one (1) ounce of engine oil through the spark plug hole into the cylinder. Crank the engine several times to distribute the oil. Replace spark plug.

Preparing Snow Thrower

•When storingthe snow thrower in an unventilated or metal storage shed, care should be taken to rustproof the equipment. Using a light oil or silicone, coat the equipment, especially any chains, springs, bearings and cables.

Remove all dirt from exterior of engine and equipment.

Follow lubrication recommendations on. Store in a clean, dry area.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Craftsman Content Two -Year Warranty on Craftsman Snow ThrowerTraining KWARNING LHI Attaching Handle Assembly Removing From CartonLoose Parts Tools RequiredAttaching Chute Crank Bolt HexUnderthisfor i HandlePanel J Chute Crank BracketLower Chute Carriage Bolt Crank Bracket Hex Lock Nut Cotter PinAttaching Clutch Cables Attaching Shift RodAttaching Turn Triggers FerruleLamp Wiring Final AdjustmentsAdjusting Traction Drive Control Adjusting Skid ShoeMake sure that the spark plug is disconnected Hex NutMeets Ansi Safety Standards Knowing Your Snow ThrowerChute Crank Discharge ChuteOperating Controls Before Starting Engine To Start EngineElectric Starter Cold StartOperating Snow Thrower Warm StartRecoil Starter Frozen Recoil StarterTo Throw Snow Operating TipsBefore Stopping To Engage AugersGeneral Recommendations Customer ResponsibilitiesEngine Maintenance LubricationCheck V-belts Chart Checking Oil LevelChanging Oil Spark PlugAdjustments AugersAuger Clutch Shift RodShave Plate And Skid Shoes Auger Drive BeltsSelf-Tapping Drive Belt Friction Wheel RubberBell Washer Hex Bolt Carburetor Engine OilPreparing Snow Thrower Bowl DrainPossible Cause Sears Craftsman 9.0 H.P. Snow Thrower Model Qty Sears Craftsman 9.0 H.P. Snow Thrower Model Actuator Sears Craftsman 9.0 H.P. Snow Thrower Model Key Pad No PaR No Description Qty Sears Craftsman 9.0 H.P, Snow Thrower Model Key Pa No Flat Idler ScrewCarburetor 305 100 224315 219//1 3t0GMCR Flywheel Nut220 35438 Choke Knob Recoil Starter 8OO-4-REPAIR

247.88851 specifications

The Craftsman 247.88851 is a standout lawn mower, designed to meet the needs of homeowners looking for a reliable and efficient gardening solution. This model combines innovative features with user-friendly technology to provide an exceptional mowing experience. Its power and performance are backed by a robust 21-inch cutting deck, making it ideal for tackling small to medium-sized yards with precision.

One of the notable features of the Craftsman 247.88851 is its 140cc engine. This engine offers sufficient power to handle various grass types and conditions, ensuring a clean and even cut every time. The starting mechanism boasts a reliable pull-start system, simplifying the operation and enhancing user convenience. This model also incorporates a 5-position height adjustment feature, allowing users to customize their mowing height according to their lawn's specific needs.

The Craftsman 247.88851 stands out with its ease of maneuverability. Its lightweight design and compact frame facilitate effortless navigation around obstacles such as trees and garden beds. The lawn mower is equipped with 7-inch front wheels and 8-inch rear wheels, providing excellent stability and traction. This stability is crucial for achieving optimal mowing results, especially on uneven terrain.

Another remarkable technology featured in the Craftsman 247.88851 is its superior grass collection system. The mower comes with a 1.9-bushel grass bag that efficiently collects clippings, ensuring a tidy lawn finish. Alternatively, users can opt for mulching functionality, which finely cuts and distributes the clippings back into the lawn, promoting healthy growth and providing essential nutrients.

In terms of build quality, the Craftsman 247.88851 is constructed with durable materials that withstand the rigors of regular use. Its sturdy design minimizes vibrations, resulting in a smoother mowing experience while reducing operator fatigue.

Overall, the Craftsman 247.88851 is an excellent choice for homeowners seeking a powerful, efficient, and easy-to-use lawn mower. Its combination of a strong engine, precise cutting capabilities, and advanced features makes it a valuable addition to any garden maintenance toolkit. Whether tackling overgrown patches or maintaining a well-groomed lawn, this mower delivers consistent and reliable performance.
Top Page Image Contents