Husqvarna 524S Before Starting the Engine, To Adjust Skid Plates See Fig, ADD Gasoline See Fig

Page 11

OPERATION

TO ADJUST SKID PLATES (See Fig. 17)

NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.

Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven.

NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower.

•If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position.

1.Shut off engine and wait for all moving parts to stop.

2.Adjust skid plates by loosening the rear 1/2" hex nut only, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely.

HIGH POSITION (LOW GROUND CLEARANCE)

•To change engine oil, see “TO CHANGE ENGINE OIL” in the Maintenance section of this manual.

ADD GASOLINE (See Fig. 18)

•Fill fuel tank to bottom of tank filler neck. Do not over- fill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

CAUTION: Alcohol blended fuels (called gas- ohol or using ethanol or methanol) can attract moisture which leads to separation and for- mation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next sea- son. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

AUGER

HOUSING

SKID PLATE

1/2" HEX NUT

LOW POSITION (HIGH GROUND CLEARANCE)

FIG. 17

SCRAPER BAR

The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 18)

The engine on your snow thrower has been shipped, from the factory, already filled with oil.

CHOKE CONTROL

SAFETY

IGNITION

KEY

RECOIL

STARTER

HANDLE

THROTTLE PRIMER ENGINE OIL FILL CAP / DIPSTICK

GASOLINE

FILLER CAP

FUEL SHUT-

OFF VALVE

1.Check engine oil with snow thrower on level ground.

2.Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 18

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 524S Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Parts Packed Separately in Carton Assembly / PRE-OPERATIONTool BOX See Fig HOW to SET UP Your Snow ThrowerInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Engine HOW to USE Your Snow ThrowerStopping AugerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Scraper BAR To Adjust Skid Plates See FigBefore Starting the Engine ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Service Notes Repair Parts Repair Parts Auger Housing / Impeller Assembly Control Panel / Discharge Chute KEY Part Description Handles 532 18 41-10 Lever, Auger Control, RH Drive Repair Parts Chassis / Engine / Pulleys KEY Part Description Wheels / Decals KEY Part Description Sion Tmita ILD NA SON ITP Eexc 4ON ITC ES Rantywar Tementsta

524S specifications

The Husqvarna 524S is a high-performance handheld leaf blower designed for both residential and professional use. It is a prime example of Husqvarna's commitment to providing powerful and efficient tools for outdoor maintenance. With a sleek design and innovative features, the 524S makes yard cleanup tasks easier and more effective.

One of the standout features of the Husqvarna 524S is its powerful yet efficient engine. Powered by a 25cc two-stroke engine, it delivers impressive air speeds and volume, making it capable of handling heavy leaves, grass clippings, and debris. The engine is designed to provide excellent fuel efficiency, ensuring that users can work longer on a single tank without compromising on performance.

The Husqvarna 524S employs advanced X-Torq engine technology, which reduces harmful emissions and increases fuel efficiency by up to 20%. This technology not only contributes to a greener environment but also means that operators can work without the constant worry of excessive noise and emissions, making it suitable for use in residential neighborhoods.

Another notable characteristic of the 524S is its lightweight design. Weighing in at just under 5 pounds, this blower is easy to maneuver, reducing user fatigue during extended periods of operation. The comfortable ergonomic handle ensures a secure grip, providing excellent control and reducing strain on the hands and arms.

In addition to its powerful performance, the Husqvarna 524S includes several user-friendly features. The cruise control function allows users to maintain a consistent airspeed, which is particularly useful for longer tasks such as clearing large areas of leaves. The blower's adjustable nozzle further enhances versatility by allowing users to customize the airflow direction according to their specific needs.

Moreover, Husqvarna has integrated a smart start feature into the 524S, which simplifies the starting process. This technology reduces the amount of effort needed to pull the starter cord, making it easier for users of all experience levels to get the blower up and running quickly.

The durable construction of the Husqvarna 524S ensures that it can withstand the rigors of frequent use. From the high-quality materials used in its manufacture to its robust build, this leaf blower is designed for longevity, making it a wise investment for anyone in need of dependable outdoor equipment.

In summary, the Husqvarna 524S is a well-rounded leaf blower that combines power, efficiency, and user-friendly features. With its lightweight design, advanced engine technology, and ease of use, it stands out as an excellent choice for both homeowners and professionals seeking reliable outdoor equipment for leaf and debris management.
Top Page Image Contents