Husqvarna 524S owner manual Safe Operation Practices for Walk-Behind Snow Throwers

Page 2

IMPORTANT

Safe Operation Practices for Walk-Behind Snow Throwers

This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury.

Look for this symbol to point out im- portant safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED.

WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent acci- dental starting when setting up, trans- porting, adjusting or making repairs.

WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be exercised while using on sloping sur- faces. Do not use snow thrower on surfaces above ground level such as roofs of residences, garages, porches or other such structures or buildings.

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

CAUTION: Muffler and other engine parts become extremely hot during operation and remain hot after engine has stopped. To avoid severe burns on contact, stay away from these areas.

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemi- cals known to the State of California to cause cancer and birth defects or other reproductive harm.

Training

1.Read, understand and follow all instructions on the machine and in the manual(s) before operating this unit. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.

2.Never allow children to operate the equipment. Never allow adults to operate the equipment without proper instruction.

3.Keep the area of operation clear of all persons, par- ticularly small children.

4.Exercise caution to avoid slipping or falling, especially when operating the snow thrower in reverse.

Preparation

1.Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires, and other foreign objects.

2.Disengage all clutches and shift into neutral before starting the engine (motor).

3.Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear footwear that will improve footing on slippery surfaces.

4.Handle fuel with care; it is highly flammable

(a)Use an approved fuel container.

(b)Never add fuel to a running engine or hot en- gine.

(c)Fill fuel tank outdoors with extreme care. Never fill fuel tank indoors.

(d)Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place contain- ers on the ground, away from your vehicle, before filling.

(e)When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dispenser nozzle.

(f)Keep the nozzle in contact with the rim of the fuel tank or container opening at all times, until refuel- ing is complete. Do not use a nozzle lock-open device.

(g)Replace gasoline cap securely and wipe up spilled fuel.

(h)If fuel is spilled on clothing, change clothing im- mediately.

5.Use extension cords and receptacles as specified by the manufacturer for all units with electric drive motors or electric starting motors.

6.Adjust the collector housing height to clear gravel or crushed rock surface.

7.Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer).

8.Always wear safety glasses or eye shields during op- eration or while performing an adjustment or repair to protect eyes from foreign objects that may be thrown from the machine.

Operation

1.Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.

2.Exercise extreme caution when operating on or cross- ing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic.

3.After striking a foreign object, stop the engine (motor), remove the wire from the spark plug, disconnect the cord on electric motors, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower.

4.If the unit should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

5.Stop the engine (motor) whenever you leave the oper- ating position, before unclogging the collector/impeller

 

housing or discharge chute, and when making any

2

repairs, adjustments or inspections.

 

Page 1 Page 3
Image 2
Page 1 Page 3
Contents 524S Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Speed Control ROD See Figs Tool BOX See FigCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Auger HOW to USE Your Snow ThrowerStopping EngineTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig ADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BARBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Service Notes Repair Parts Repair Parts Auger Housing / Impeller Assembly Control Panel / Discharge Chute KEY Part Description Handles 532 18 41-10 Lever, Auger Control, RH Drive Repair Parts Chassis / Engine / Pulleys KEY Part Description Wheels / Decals KEY Part Description Rantywar Tementsta Sion Tmita ILD NA SON ITP Eexc 4ON ITC ES

524S specifications

The Husqvarna 524S is a high-performance handheld leaf blower designed for both residential and professional use. It is a prime example of Husqvarna's commitment to providing powerful and efficient tools for outdoor maintenance. With a sleek design and innovative features, the 524S makes yard cleanup tasks easier and more effective.

One of the standout features of the Husqvarna 524S is its powerful yet efficient engine. Powered by a 25cc two-stroke engine, it delivers impressive air speeds and volume, making it capable of handling heavy leaves, grass clippings, and debris. The engine is designed to provide excellent fuel efficiency, ensuring that users can work longer on a single tank without compromising on performance.

The Husqvarna 524S employs advanced X-Torq engine technology, which reduces harmful emissions and increases fuel efficiency by up to 20%. This technology not only contributes to a greener environment but also means that operators can work without the constant worry of excessive noise and emissions, making it suitable for use in residential neighborhoods.

Another notable characteristic of the 524S is its lightweight design. Weighing in at just under 5 pounds, this blower is easy to maneuver, reducing user fatigue during extended periods of operation. The comfortable ergonomic handle ensures a secure grip, providing excellent control and reducing strain on the hands and arms.

In addition to its powerful performance, the Husqvarna 524S includes several user-friendly features. The cruise control function allows users to maintain a consistent airspeed, which is particularly useful for longer tasks such as clearing large areas of leaves. The blower's adjustable nozzle further enhances versatility by allowing users to customize the airflow direction according to their specific needs.

Moreover, Husqvarna has integrated a smart start feature into the 524S, which simplifies the starting process. This technology reduces the amount of effort needed to pull the starter cord, making it easier for users of all experience levels to get the blower up and running quickly.

The durable construction of the Husqvarna 524S ensures that it can withstand the rigors of frequent use. From the high-quality materials used in its manufacture to its robust build, this leaf blower is designed for longevity, making it a wise investment for anyone in need of dependable outdoor equipment.

In summary, the Husqvarna 524S is a well-rounded leaf blower that combines power, efficiency, and user-friendly features. With its lightweight design, advanced engine technology, and ease of use, it stands out as an excellent choice for both homeowners and professionals seeking reliable outdoor equipment for leaf and debris management.
Top Page Image Contents