Husqvarna 524S owner manual Engine, Cleaning

Page 14

MAINTENANCE

V-BELTS

Check V-belts for deterioration and wear after every 50 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear. (See “TO REMOVE BELT COVER” in the Service and Adjustments section of this manual).

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

AUGER GEAR CASE

•The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

•If lubricant is required, use only Ronex ED #1 grease.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance.

CAUTION: Any lubricating of the above compo- nents can cause contamination of the friction wheel and damage to the drive system of your snow thrower.

ENGINE

See engine manual.

LUBRICATION

Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature.

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 25 hours of operation or at least once a year if the snow thrower is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil fill cap / dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range anticipated before next oil change. All oil must meet API service classification SG–SL.

•Be sure snow thrower is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

NOTE: The left side wheel may be removed from snow thrower for easier access to the oil drain plug and place- ment of a suitable container. The unit tilted, resting on the frame with the left wheel removed, will help drain any oil trapped inside the engine. (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Clean area around drain plug.

3.Remove drain plug and drain oil in a suitable container.

4.Install drain plug and tighten securely.

5.Wipe off any spilled oil from snow thrower and engine.

6.Install left wheel (if removed for draining oil). Be sure to install klick pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual).

7.Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine.

8.Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual.

9.Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

10.Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a fire hazard and/or damage.

SPARK PLUG

Replace spark plug at the beginning of each season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in the “PRODUCT SPECIFICATIONS” section of this manual.

CLEANING

IMPORTANT: For best performance, keep snow thrower housing free of any dirt or trash. Clean the outside of your snow thrower after each use.

WARNING: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

•Keep finished surfaces/wheels free of gasoline, oil, etc.

•We do not recommend using a garden hose to clean your snow thrower unless the electrical system, muffler and carburetor are covered to keep water out. Water in engine can result in shortened engine life.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 524S Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs HOW to SET UP Your Snow ThrowerInstall Speed Control ROD See Figs Tool BOX See FigCheck Tire Pressure Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Auger HOW to USE Your Snow ThrowerStopping EngineTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig ADD Gasoline See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BARBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Service Notes Repair Parts Repair Parts Auger Housing / Impeller Assembly Control Panel / Discharge Chute KEY Part Description Handles 532 18 41-10 Lever, Auger Control, RH Drive Repair Parts Chassis / Engine / Pulleys KEY Part Description Wheels / Decals KEY Part Description Rantywar Tementsta Sion Tmita ILD NA SON ITP Eexc 4ON ITC ES

524S specifications

The Husqvarna 524S is a high-performance handheld leaf blower designed for both residential and professional use. It is a prime example of Husqvarna's commitment to providing powerful and efficient tools for outdoor maintenance. With a sleek design and innovative features, the 524S makes yard cleanup tasks easier and more effective.

One of the standout features of the Husqvarna 524S is its powerful yet efficient engine. Powered by a 25cc two-stroke engine, it delivers impressive air speeds and volume, making it capable of handling heavy leaves, grass clippings, and debris. The engine is designed to provide excellent fuel efficiency, ensuring that users can work longer on a single tank without compromising on performance.

The Husqvarna 524S employs advanced X-Torq engine technology, which reduces harmful emissions and increases fuel efficiency by up to 20%. This technology not only contributes to a greener environment but also means that operators can work without the constant worry of excessive noise and emissions, making it suitable for use in residential neighborhoods.

Another notable characteristic of the 524S is its lightweight design. Weighing in at just under 5 pounds, this blower is easy to maneuver, reducing user fatigue during extended periods of operation. The comfortable ergonomic handle ensures a secure grip, providing excellent control and reducing strain on the hands and arms.

In addition to its powerful performance, the Husqvarna 524S includes several user-friendly features. The cruise control function allows users to maintain a consistent airspeed, which is particularly useful for longer tasks such as clearing large areas of leaves. The blower's adjustable nozzle further enhances versatility by allowing users to customize the airflow direction according to their specific needs.

Moreover, Husqvarna has integrated a smart start feature into the 524S, which simplifies the starting process. This technology reduces the amount of effort needed to pull the starter cord, making it easier for users of all experience levels to get the blower up and running quickly.

The durable construction of the Husqvarna 524S ensures that it can withstand the rigors of frequent use. From the high-quality materials used in its manufacture to its robust build, this leaf blower is designed for longevity, making it a wise investment for anyone in need of dependable outdoor equipment.

In summary, the Husqvarna 524S is a well-rounded leaf blower that combines power, efficiency, and user-friendly features. With its lightweight design, advanced engine technology, and ease of use, it stands out as an excellent choice for both homeowners and professionals seeking reliable outdoor equipment for leaf and debris management.
Top Page Image Contents