Husqvarna ST 224 warranty INSTALLDISCHARGECHUTE/CHUTEROTATORHEAD See, Check Tire Pressure

Page 6

ASSEMBLY / PRE-OPERATION

INSTALLDISCHARGECHUTE/CHUTEROTATORHEAD (See Fig. 4 and 5)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotator head over chute bracket. If neces- sary, rotate chute assembly to align square and pin on un- derside of chute rotator head with holes in chute bracket.

3.With chute rotator head and chute bracket aligned, position chute rotator head on pin and threaded stud of mounting bracket.

4.Install locknut and cable guide on threaded stud and tighten securely.

CHUTE

LOCKNUT

 

CABLE GUIDE

ROTATOR

 

 

HEAD

 

 

 

 

PIN

 

 

THREADED

 

 

STUD

 

ROTATOR HEAD

CHUTE

ALIGN BEFORE

MOUNTING

BRACKET

TIGHTENING LOCKNUT

BRACKET

FIG. 4

5.Place rotator cables through cable guide and secure cables to the lower handle using the double clip.

ROTATOR

 

CABLES

CABLE GUIDE

 

DOUBLE

 

CLIP

 

ROTATOR

 

CABLES

 

FIG. 5

 

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 6 and 7)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten nut securely. Eyelet will be loose on shoulder bolt.

3.Install spring hooks between hex nuts on chute rotator head and into hole in chute deflector as shown.

SPRING

CHUTE

1/4-20

DEFLECTOR

SHOULDER

 

BOLT

HOOK

 

BETWEEN

 

HEX NUTS

 

ON CHUTE

1/4-20

ROTATOR

LOCKNUT

HEAD

 

5/16-18

 

CARRIAGE

 

BOLT

CABLE

 

EYELET

 

REMOTE

 

CABLE

 

BRACKET

 

5/16-18

 

LOCKNUT

 

FIG. 6

4.Install all 3 control lever knobs by pressing them down onto the control levers.

KNOB

KNOB

 

CONTROL LEVER

FIG. 7

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Operator’s Manual Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Carriage BoltsRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper Handle See FigsINSTALLDISCHARGECHUTE/CHUTEROTATORHEAD See Install Chute Deflector Remote Control See FigsCheck Tire Pressure Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig To Move Forward and Backward See FigScraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning Snow ThrowerEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts Auger Belt Replacement See FigTo Install Auger Belt Before Replacing BeltsTo Remove Wheels See Fig Drive Belt Replacement See FigAfter Replacing Belts CarburetorTo Adjust Chute Rotator Cable Tension See Fig Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionConsumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below Service Notes Service Notes Service Notes 07/09/2014 BD

ST 224 specifications

The Husqvarna ST 224 is a powerful, versatile snowblower designed to tackle even the harshest winter conditions. Built for residential use, this reliable two-stage snow thrower excels in clearing medium to large-sized driveways, sidewalks, and parking areas, efficiently managing snow up to 12 inches deep.

One of the standout features of the ST 224 is its robust engine. It is powered by a reliable 223cc Husqvarna engine, which delivers impressive performance and durability. The engine’s efficient design allows for easy starting, even in frigid temperatures. With a maximum throwing distance of approximately 33 feet, this snowblower can rapidly discharge snow, making quick work of winter's toughest tasks.

The snowblower is equipped with a 24-inch wide clearing width and a 23-inch intake height, allowing it to accommodate heavy snowfall with ease. The auger system efficiently collects snow, while the impeller system provides powerful throwing capabilities. This combination ensures that users can clear snow quickly and efficiently.

Husqvarna has incorporated several user-friendly features into the ST 224, making it easy to operate. The adjustable skid shoes allow users to customize the height of the machine relative to the surface being cleared, preventing damage to driveways or sidewalks. The remote chute rotation and deflector adjustment enable users to aim the snow where they want it to go with minimal effort.

When it comes to maneuverability, the Husqvarna ST 224 shines. It features large, deep-tread wheels that provide excellent traction, even in icy conditions. This mobility is further enhanced by the lightweight construction of the snowblower, making it easy to handle and operate.

The snowblower's durable construction ensures longevity, even during demanding use. The steel frame and housing provide the necessary robustness, while the corrosion-resistant materials ensure that the machine can withstand the wear and tear of winter weather.

Overall, the Husqvarna ST 224 combines power, efficiency, and user-friendly features. It’s an ideal choice for homeowners who need a reliable snowblower that can handle heavy snowfall, offering exceptional performance and ease of use throughout the winter months. With its impressive features and technologies, the Husqvarna ST 224 stands out as a top choice for residential snow removal.
Top Page Image Contents