Husqvarna ST 224 warranty Meets A.N.S.I. Safety Requirements

Page 8

OPERATION

MUFFLER

POWER CORD

AUGER

 

CONTROL

GASOLINE

PLUG

LEVER

FILLER CAP

 

 

 

CHOKE

ELECTRIC

 

CONTROL

START

 

ON / OFF

BUTTON

 

 

 

SWITCH

 

 

 

 

LIGHT

PRIMER

SAFETY

IGNITION

KEY

FUEL SHUT-OFF VALVE

RECOIL STARTER HANDLE

CHUTE

DEFLECTOR

CLEAN-OUT TOOL

DISCHARGE CHUTE

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY VARY

WITH THE ENGINE

ON YOUR UNIT.

AUGERS

SKID PLATE

 

 

FIG. 8

DISCHARGE CHUTE CONTROL LEVER

DRIVE SPEED

CONTROL LEVER

DEFLECTOR

REMOTE

CONTROL

LEVER

TRACTION

DRIVE

CONTROL

LEVER

HANDLE KNOB

MUFFLER

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting engine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke Control - used for starting a cold engine. ON / OFF switch - used to STOP the engine.

Fuel shut off valve - used for shutting off the fuel flow to the engine.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power- propelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the direc- tion the snow is thrown.

Deflector remote control lever - used to change the distance the snow is thrown.

Skid plate - used to adjust height of scraper bar from the ground.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Operator’s Manual Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Carriage BoltsAssembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper Handle See FigsCheck Tire Pressure INSTALLDISCHARGECHUTE/CHUTEROTATORHEAD SeeInstall Chute Deflector Remote Control See Figs Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationEngine CleaningSnow Thrower Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigAuger Belt Replacement See Fig To Install Auger BeltTo Replace Belts Before Replacing BeltsDrive Belt Replacement See Fig After Replacing BeltsTo Remove Wheels See Fig CarburetorTo Adjust Chute Rotator Cable Tension See Fig Storage OtherFuel System Engine OILTroubleshooting Problem Cause CorrectionConsumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below Service Notes Service Notes Service Notes 07/09/2014 BD

ST 224 specifications

The Husqvarna ST 224 is a powerful, versatile snowblower designed to tackle even the harshest winter conditions. Built for residential use, this reliable two-stage snow thrower excels in clearing medium to large-sized driveways, sidewalks, and parking areas, efficiently managing snow up to 12 inches deep.

One of the standout features of the ST 224 is its robust engine. It is powered by a reliable 223cc Husqvarna engine, which delivers impressive performance and durability. The engine’s efficient design allows for easy starting, even in frigid temperatures. With a maximum throwing distance of approximately 33 feet, this snowblower can rapidly discharge snow, making quick work of winter's toughest tasks.

The snowblower is equipped with a 24-inch wide clearing width and a 23-inch intake height, allowing it to accommodate heavy snowfall with ease. The auger system efficiently collects snow, while the impeller system provides powerful throwing capabilities. This combination ensures that users can clear snow quickly and efficiently.

Husqvarna has incorporated several user-friendly features into the ST 224, making it easy to operate. The adjustable skid shoes allow users to customize the height of the machine relative to the surface being cleared, preventing damage to driveways or sidewalks. The remote chute rotation and deflector adjustment enable users to aim the snow where they want it to go with minimal effort.

When it comes to maneuverability, the Husqvarna ST 224 shines. It features large, deep-tread wheels that provide excellent traction, even in icy conditions. This mobility is further enhanced by the lightweight construction of the snowblower, making it easy to handle and operate.

The snowblower's durable construction ensures longevity, even during demanding use. The steel frame and housing provide the necessary robustness, while the corrosion-resistant materials ensure that the machine can withstand the wear and tear of winter weather.

Overall, the Husqvarna ST 224 combines power, efficiency, and user-friendly features. It’s an ideal choice for homeowners who need a reliable snowblower that can handle heavy snowfall, offering exceptional performance and ease of use throughout the winter months. With its impressive features and technologies, the Husqvarna ST 224 stands out as a top choice for residential snow removal.
Top Page Image Contents