Husqvarna ST 224 warranty HOW to USE Your Snow Thrower, Stopping

Page 9

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields while operating your snow thrower or performing any adjust- ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

•Release the auger control lever to stop throwing snow.

ENGINE

1.Move ON / OFF switch to “OFF” position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE FUEL SHUT-OFF VALVE (See Fig. 9)

The fuel shut-off valve is located beneath the fuel tank on the engine. Always operate the snow thrower with the fuel shut-off valve in the OPEN position.

OFF

OPEN

FIG. 9

TO USE CHOKE CONTROL (See Fig. 10)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

•To engage choke, rotate lever clockwise to “FULL” position.

CHOKE

CONTROL

CONTROL

CHOKE

 

 

TRUCTIONS

FIG. 10

TO CONTROL SNOW DISCHARGE (See Fig. 11)

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: If the discharge chute or au- ger become clogged, shut-off engine and wait for all moving parts to stop. Use the clean-out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever.

•To change the discharge chute position, pull backward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther.

•Push right on chute deflector control lever and move lever forward to lower the deflector and decrease the distance. Move lever back to raise the deflector and increase the distance. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROL LEVER

CHUTE DEFLECTOR

REMOTE CONTROL

LEVER

FIG. 11

TO THROW SNOW (See Fig. 12)

The auger rotation is controlled by the auger control lever located on the right side handle.

•Squeeze auger control lever to handle to engage the auger and throw snow.

•Release the auger control lever to stop throwing snow.

AUGER

CONTROL

LEVER

FIG. 12

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Operator’s Manual Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Carriage Bolts Parts Packed Separately in CartonHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper Handle See FigsINSTALLDISCHARGECHUTE/CHUTEROTATORHEAD See Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower OperationRecoil auxiliary starter handle used for starting engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigBefore Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationCleaning Snow ThrowerEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Install Auger Belt Auger Belt Replacement See FigTo Replace Belts Before Replacing BeltsAfter Replacing Belts Drive Belt Replacement See FigTo Remove Wheels See Fig CarburetorTo Adjust Chute Rotator Cable Tension See Fig Other StorageFuel System Engine OILProblem Cause Correction TroubleshootingConsumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Armor Protected Stamped Deck Shell Example Below Service Notes Service Notes Service Notes 07/09/2014 BD

ST 224 specifications

The Husqvarna ST 224 is a powerful, versatile snowblower designed to tackle even the harshest winter conditions. Built for residential use, this reliable two-stage snow thrower excels in clearing medium to large-sized driveways, sidewalks, and parking areas, efficiently managing snow up to 12 inches deep.

One of the standout features of the ST 224 is its robust engine. It is powered by a reliable 223cc Husqvarna engine, which delivers impressive performance and durability. The engine’s efficient design allows for easy starting, even in frigid temperatures. With a maximum throwing distance of approximately 33 feet, this snowblower can rapidly discharge snow, making quick work of winter's toughest tasks.

The snowblower is equipped with a 24-inch wide clearing width and a 23-inch intake height, allowing it to accommodate heavy snowfall with ease. The auger system efficiently collects snow, while the impeller system provides powerful throwing capabilities. This combination ensures that users can clear snow quickly and efficiently.

Husqvarna has incorporated several user-friendly features into the ST 224, making it easy to operate. The adjustable skid shoes allow users to customize the height of the machine relative to the surface being cleared, preventing damage to driveways or sidewalks. The remote chute rotation and deflector adjustment enable users to aim the snow where they want it to go with minimal effort.

When it comes to maneuverability, the Husqvarna ST 224 shines. It features large, deep-tread wheels that provide excellent traction, even in icy conditions. This mobility is further enhanced by the lightweight construction of the snowblower, making it easy to handle and operate.

The snowblower's durable construction ensures longevity, even during demanding use. The steel frame and housing provide the necessary robustness, while the corrosion-resistant materials ensure that the machine can withstand the wear and tear of winter weather.

Overall, the Husqvarna ST 224 combines power, efficiency, and user-friendly features. It’s an ideal choice for homeowners who need a reliable snowblower that can handle heavy snowfall, offering exceptional performance and ease of use throughout the winter months. With its impressive features and technologies, the Husqvarna ST 224 stands out as a top choice for residential snow removal.
Top Page Image Contents