Husqvarna 96193005400, 1830HV manual Snow Throwing Tips, To Start Engine, Before Stopping

Page 13

OPERATION

TO START ENGINE

•Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current.

•Be sure your house is a 120 Volt A.C. three-wire grounded system. If you are uncertain, consult a licensed electrician.

WARNING: Do not use the electric starter if your house is not a 120 Volt A.C. three-wire grounded system. Seri- ous personal injury or damage to your snow thrower could result.

COLD START - ELECTRIC STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Move choke control to “FULL” position.

4.Connect the power cord to the engine.

5.Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle.

NOTE: Do not use primer when starting engine with the electric starter.

6. Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five continu- ous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt.

7.When the engine starts, release the starter button and slowly move the choke control to the “OFF” position.

8.Disconnect the power cord from the receptacle first, then from the engine.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the “OFF” position.

COLD START - RECOIL STARTER

1.Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra safety ignition key in a safe place.

2.Place ON / OFF switch in “ON” position.

3.Rotate choke control to “FULL” position.

4.Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary.

NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer.

5.Pull recoil starter handle quickly. Do not allow starter rope to snap back.

6.When the engine starts, release the recoil starter handle and slowly move the choke control to the “OFF” posi- tion.

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operat- ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF” position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois- ture on the engine.

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine, proceed as follows:

1.Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible.

2.Release the recoil starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the above steps or use the electric starter.

SNOW THROWING TIPS

•Go slower in deep, freezing or heavy wet snow. Use the drive speed control, NOT the ON / OFF switch, to adjust speed.

•It is easier and more efficient to remove snow imme- diately after it falls.

•The best time to remove snow is the early morning. At this time the snow is usually dry and has not been ex- posed to the direct sun and warming temperatures.

•Slightly overlap each successive path to ensure all snow will be removed.

•Throw snow downwind whenever possible.

•Adjust the skid plates to proper height for current snow conditions. See “TO ADJUST SKID PLATES” in this section of this manual.

•For extremely heavy snow, reduce the width of snow removal by overlapping previous path and moving slowly.

•Keep engine clean and clear of snow during use. This will help air flow and extend engine life.

•After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine.

•Clean the entire snow thrower thoroughly after each use and wipe dry so it is ready for next use.

WARNING: Do not operate snow thrower if weather conditions impair visibility. Throwing snow during a heavy, windy snowstorm can blind you and be hazardous to the safe operation of the snow thrower.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 1830HV Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer TractionRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigRelease the auger control lever and shut off the engine To Move Forward and Backward See FigBefore Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigRemove the klik pin and remove wheel from axle CarburetorOther StorageFuel System Engine OILTroubleshooting Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart 532 43 54-80 05.20.10 TH See Separate Engine Manufacturers or Manufacturers warranty

96193005400, 1830HV specifications

The Husqvarna 1830HV, model number 96193005400, is a powerful and versatile snow blower designed for homeowners who need to tackle heavy snowfalls efficiently. This machine is engineered with advanced features that make snow removal a breeze, ensuring your driveway and pathways are clear throughout the winter season.

One of the standout features of the Husqvarna 1830HV is its robust 369cc engine. This engine is designed for high performance, delivering the necessary power to handle thick, heavy snow. The electric start function enhances user convenience, allowing for easier ignition in cold weather conditions. With a clearing width of 30 inches, this snow blower can clear a substantial amount of snow with each pass, making it suitable for larger driveways and sidewalks.

The Husqvarna 1830HV boasts a unique Hydrostatic transmission that provides smooth and effective operation. This feature allows the operator to adjust the speed easily, giving them greater control over the snow clearing process. Additionally, the dual-stage system employs an auger and impeller design, ensuring efficient snow intake and throwing capability, capable of launching snow up to 50 feet away.

Another impressive characteristic is the adjustable drift cutters, which help to manage high snow drifts effectively. The machine also features remote chute rotation and deflection, allowing users to easily direct the expelled snow exactly where it’s needed, without stopping or leaving the operator's position.

User comfort is a priority in the design of the Husqvarna 1830HV. The ergonomically designed controls make it easy to operate, even in gloves, while the heated grips provide warmth during the coldest conditions. The LED headlights enhance visibility during early mornings or evenings, ensuring users can work safely and effectively at any hour.

Durability is guaranteed with the rugged construction of the Husqvarna 1830HV. Built with high-quality materials, it’s designed to withstand harsh winter conditions, making it a reliable choice for homeowners looking for a snow blower that can last through the seasons. In summary, the Husqvarna 1830HV, 96193005400 is an outstanding snow blower, combining power, efficiency, and user-friendly design to tackle winter challenges with ease.
Top Page Image Contents