Husqvarna 96193005400, 1830HV manual To Replace Belts See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 22)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a Sears service center/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest Sears service center/department. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding the auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE HAIRPIN FROM CLUTCH ROD and re- move clutch rod from swing plate. Tip swing plate forward.

7.REMOVE AUGER BELT from around pulley.

8.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

9.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

10.Install clutch rod in swing plate; secure with hairpin.

11.Place auger belt around and inside the groove of auger pulley only.

12.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

13.Move idler arm so it does not hit impeller pulley as you bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 12. Belt must be fully seated in pulley groove when bringing the snow thrower together.

14.Install the two (2) hex bolts and tighten securely.

15.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

16.INSTALL BELT COVER and two (2) screws. Tighten securely.

17.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

TRACTION DRIVE BELT

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

BOLT

IDLER ARM

AUGER

SQUARE

BELT

HOLE

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

17

FIG. 22

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 1830HV Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsKnow Your Snow Thrower OperationPrimer TractionRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigRelease the auger control lever and shut off the engine To Move Forward and Backward See FigBefore Starting the Engine To Adjust Skid Plates See FigScraper BAR See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Remove Wheels See Fig To Adjust Cable Tension See FigRemove the klik pin and remove wheel from axle CarburetorOther StorageFuel System Engine OILTroubleshooting Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart 532 43 54-80 05.20.10 TH See Separate Engine Manufacturers or Manufacturers warranty

96193005400, 1830HV specifications

The Husqvarna 1830HV, model number 96193005400, is a powerful and versatile snow blower designed for homeowners who need to tackle heavy snowfalls efficiently. This machine is engineered with advanced features that make snow removal a breeze, ensuring your driveway and pathways are clear throughout the winter season.

One of the standout features of the Husqvarna 1830HV is its robust 369cc engine. This engine is designed for high performance, delivering the necessary power to handle thick, heavy snow. The electric start function enhances user convenience, allowing for easier ignition in cold weather conditions. With a clearing width of 30 inches, this snow blower can clear a substantial amount of snow with each pass, making it suitable for larger driveways and sidewalks.

The Husqvarna 1830HV boasts a unique Hydrostatic transmission that provides smooth and effective operation. This feature allows the operator to adjust the speed easily, giving them greater control over the snow clearing process. Additionally, the dual-stage system employs an auger and impeller design, ensuring efficient snow intake and throwing capability, capable of launching snow up to 50 feet away.

Another impressive characteristic is the adjustable drift cutters, which help to manage high snow drifts effectively. The machine also features remote chute rotation and deflection, allowing users to easily direct the expelled snow exactly where it’s needed, without stopping or leaving the operator's position.

User comfort is a priority in the design of the Husqvarna 1830HV. The ergonomically designed controls make it easy to operate, even in gloves, while the heated grips provide warmth during the coldest conditions. The LED headlights enhance visibility during early mornings or evenings, ensuring users can work safely and effectively at any hour.

Durability is guaranteed with the rugged construction of the Husqvarna 1830HV. Built with high-quality materials, it’s designed to withstand harsh winter conditions, making it a reliable choice for homeowners looking for a snow blower that can last through the seasons. In summary, the Husqvarna 1830HV, 96193005400 is an outstanding snow blower, combining power, efficiency, and user-friendly design to tackle winter challenges with ease.
Top Page Image Contents