Husqvarna 96193005400, 1830HV manual Table of Contents

Page 3

6.When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and work- ing.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16. Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the dis- charge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and manufac- tured to give best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity 2 Quarts (1,9 Liters)

and Type:

Unleaded Regular only

 

 

Oil Type

SAE 30 (above 50°F)

(API SG–SL):

SAE 5W-30 or 10W-30 (32° to 50°F)

 

SAE 5W-30 (below 32°F)

 

 

Oil Capacity:

20 Ounces (0,57 Liters)

 

 

Spark Plug:

Champion RN9YC

Gap:

0.030" (0,762 mm)

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES

2-3

PRODUCT SPECIFICATIONS

3

CUSTOMER RESPONSIBILITIES

3

ASSEMBLY / PRE-OPERATION

4-7

OPERATION

8-13

MAINTENANCE SCHEDULE

14

MAINTENANCE

14-15

SERVICE AND ADJUSTMENTS

16-18

STORAGE

19

TROUBLESHOOTING

20

WARRANTY

21-24

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 1830HV Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsTraction OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Release the auger control lever and shut off the engineCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Remove the klik pin and remove wheel from axleEngine OIL StorageOther Fuel SystemTroubleshooting Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart 532 43 54-80 05.20.10 TH See Separate Engine Manufacturers or Manufacturers warranty

96193005400, 1830HV specifications

The Husqvarna 1830HV, model number 96193005400, is a powerful and versatile snow blower designed for homeowners who need to tackle heavy snowfalls efficiently. This machine is engineered with advanced features that make snow removal a breeze, ensuring your driveway and pathways are clear throughout the winter season.

One of the standout features of the Husqvarna 1830HV is its robust 369cc engine. This engine is designed for high performance, delivering the necessary power to handle thick, heavy snow. The electric start function enhances user convenience, allowing for easier ignition in cold weather conditions. With a clearing width of 30 inches, this snow blower can clear a substantial amount of snow with each pass, making it suitable for larger driveways and sidewalks.

The Husqvarna 1830HV boasts a unique Hydrostatic transmission that provides smooth and effective operation. This feature allows the operator to adjust the speed easily, giving them greater control over the snow clearing process. Additionally, the dual-stage system employs an auger and impeller design, ensuring efficient snow intake and throwing capability, capable of launching snow up to 50 feet away.

Another impressive characteristic is the adjustable drift cutters, which help to manage high snow drifts effectively. The machine also features remote chute rotation and deflection, allowing users to easily direct the expelled snow exactly where it’s needed, without stopping or leaving the operator's position.

User comfort is a priority in the design of the Husqvarna 1830HV. The ergonomically designed controls make it easy to operate, even in gloves, while the heated grips provide warmth during the coldest conditions. The LED headlights enhance visibility during early mornings or evenings, ensuring users can work safely and effectively at any hour.

Durability is guaranteed with the rugged construction of the Husqvarna 1830HV. Built with high-quality materials, it’s designed to withstand harsh winter conditions, making it a reliable choice for homeowners looking for a snow blower that can last through the seasons. In summary, the Husqvarna 1830HV, 96193005400 is an outstanding snow blower, combining power, efficiency, and user-friendly design to tackle winter challenges with ease.
Top Page Image Contents