Husqvarna 1830HV manual Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 20)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shoulder/shear bolt and hex nut. Should a for- eign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shoulder/shear bolt and spacer. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Connect spark plug wire to spark plug. Replace safety ignition key

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared. To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Connect spark plug wire to spark plug.

1/4-20 x 1-5/8

1/4-20 x 2

CAPSCREW /

SHOULDER /

SHEAR BOLT

SHEAR BOLT

IMPELLER

 

HUB

 

1/4-20

 

LOCKNUT

 

 

AUGER HUB

 

1/4-20 LOCKNUT

 

AUGER

 

SHAFT

 

IMPELLER

 

SHAFT

FIG. 20

TO REMOVE BELT COVER (See Fig. 21)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

3.Replace belt cover by installing cover and screws and tighten securely.

BELT

COVER

FRAME

SCREWS

FIG. 21

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 1830HV Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer TractionMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigRelease the auger control lever and shut off the engine To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigRemove the klik pin and remove wheel from axle CarburetorStorage OtherFuel System Engine OILTroubleshooting Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart See Separate Engine Manufacturers or Manufacturers warranty 532 43 54-80 05.20.10 TH

96193005400, 1830HV specifications

The Husqvarna 1830HV, model number 96193005400, is a powerful and versatile snow blower designed for homeowners who need to tackle heavy snowfalls efficiently. This machine is engineered with advanced features that make snow removal a breeze, ensuring your driveway and pathways are clear throughout the winter season.

One of the standout features of the Husqvarna 1830HV is its robust 369cc engine. This engine is designed for high performance, delivering the necessary power to handle thick, heavy snow. The electric start function enhances user convenience, allowing for easier ignition in cold weather conditions. With a clearing width of 30 inches, this snow blower can clear a substantial amount of snow with each pass, making it suitable for larger driveways and sidewalks.

The Husqvarna 1830HV boasts a unique Hydrostatic transmission that provides smooth and effective operation. This feature allows the operator to adjust the speed easily, giving them greater control over the snow clearing process. Additionally, the dual-stage system employs an auger and impeller design, ensuring efficient snow intake and throwing capability, capable of launching snow up to 50 feet away.

Another impressive characteristic is the adjustable drift cutters, which help to manage high snow drifts effectively. The machine also features remote chute rotation and deflection, allowing users to easily direct the expelled snow exactly where it’s needed, without stopping or leaving the operator's position.

User comfort is a priority in the design of the Husqvarna 1830HV. The ergonomically designed controls make it easy to operate, even in gloves, while the heated grips provide warmth during the coldest conditions. The LED headlights enhance visibility during early mornings or evenings, ensuring users can work safely and effectively at any hour.

Durability is guaranteed with the rugged construction of the Husqvarna 1830HV. Built with high-quality materials, it’s designed to withstand harsh winter conditions, making it a reliable choice for homeowners looking for a snow blower that can last through the seasons. In summary, the Husqvarna 1830HV, 96193005400 is an outstanding snow blower, combining power, efficiency, and user-friendly design to tackle winter challenges with ease.
Top Page Image Contents