Husqvarna 1330SBEXP owner manual Repair Parts Handles

Page 25

REPAIR PARTS

 

HANDLES

SNOW THROWER - MODEL NO. 1330SBEXP (96193001900), PRODUCT NO. 961 93 00-19

KEY

PART

 

NO.

NO.

DESCRIPTION

1532 40 76-49 Lever, Auger Control, RH

2532 40 76-48 Lever, Traction Drive Control, LH

4532 17 88-88 Bushing, Flange

5532 16 96-75 Retainer, Hairpin

6817 06 04-08 Screw, Hex Head

7532 17 86-52 Rod, Interlock

8532 19 95-76 Arm, Impeller Rod

9532 19 95-75 Arm, Traction Rod

10532 19 95-31 Panel, Control

11

874 78 05-24

Screw, Hex Head

5/16-18 x 1-1/2

12

874 78 05-12

Screw, Hex Head

5/16-18 x 1-3/4

13532 40 78-36 Handle Tube, LH

14532 40 78-35 Handle Tube, RH

15532 75 11-53 Nut, Lock 5/16-18

16819 13 13-16 Washer, Flat 3/8

17532 17 88-99 Knob, Handle

18532 19 34-47 Rod, Auger Control

19532 18 04-85 Rod, Traction Control

22 872 12 06-18 Bolt, Carriage 3/8-16 x 2-1/4

23532 18 40-87 Handle Tube, Lower

24532 19 20-91 Sleeve, Spring

25532 18 09-26 Spring, Traction Drive

26532 17 86-69 Spring, Auger Control

27 817 00 06-16 Screw, Hex Head 3/8-16 x 1

28532 19 85-59 Bushing, Pivot Lever

29532 40 57-81 Switch, Heated Handle Grips

30532 40 58-79 Console, Panel

31

532 17 52-62

Screw, Hex Head, Tapping

#10-24 x 1-1/4

32

532 18 44-71

Screw, Hex Head, Tapping

#10-24 x 1/2

33532 19 95-77 Latch, Interlock

34532 18 35-18 Bolt, Shoulder

35532 06 80-38 Nut, Lock 1/4-20

36532 17 88-31 Spring, Torsion

37532 19 38-85 Spring, Interlock

38532 17 86-66 Headlight, Halogen (Includes Bulb)

- - 532 40 16-20Bulb, Halogen

39532 17 86-68 Bezel, Headlight

40532 40 56-99 Harness, Headlight (Halogen)

41532 17 87-75 Pop Rivet

42532 19 95-78 Lever, Interlock

43532 19 96-38 Rod, Latch, Interlock

44532 19 63-38 Rod, Arm, Interlock

45532 70 02-79 Clip

46532 17 92-46 Washer

47532 19 69-43 Mounting Bracket, Handle, RH

48532 19 69-44 Mounting Bracket, Handle, LH

49532 40 58-17 Grip, Handle, Heated

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 1330SBEXP Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigScraper BAR Before Starting the EngineTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationSnow Thrower CleaningEngine To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts 532 40 KEY Part DescriptionControl Panel / Discharge Chute KEY Part Description Handles Repair Parts Handles Drive Repair Parts Chassis / Engine / Pulleys Repair Parts Repair Parts Wheels / Decals Wheels / Decals Sion Tmita ILD NA SON ITP Eexc 4ON ITC ES Rantywar Tementsta
Top Page Image Contents