Husqvarna 1130 SBEXP owner manual To Replace Belts See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 24)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a qualified service center.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt must be fully seated in pulley groove when bringing the snow thrower together.

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install flat washer, lock- washer and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

 

AUGER

SQUARE

 

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

 

 

AUGER PULLEY

 

 

 

 

BOLT

LOCK

 

 

 

WASHER

FRAME

AUGER

 

 

 

HOUSING

 

 

17

FIG. 24

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 1130SBEXP Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigScraper BAR Before Starting the EngineTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen➀ SAE 30 Motor Oil ➁ See Engine in Maintenance section MaintenanceGeneral Recommendations Before Each USEEngine CleaningSnow Thrower To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts 532 17 KEY Part DescriptionControl Panel / Discharge Chute KEY Part Description Handles Repair Parts Drive Repair Parts Chassis / Engine / Pulleys KEY Part Description Repair Parts Wheels / Decals 532 40 Wheels / DecalsSion Tmita ILD NA SON ITP Eexc 4ON ITC ES Rantywar Tementsta

1130 SBEXP specifications

The Husqvarna 1130 SBEXP is a powerful snow blower designed to tackle the challenges posed by heavy snowfall and icy conditions. With its robust construction and advanced features, it stands out as a reliable tool for both residential and commercial use.

One of the most notable features of the Husqvarna 1130 SBEXP is its impressive clearing width of 30 inches, allowing users to clear a large path quickly and efficiently. The high-performance 291cc Husqvarna engine delivers reliable power, ensuring optimal performance in even the most challenging winter conditions. This engine is designed for easy starting and operation, so users can get to work without delays.

The machine boasts a durable steel auger that not only breaks up packed snow but also effectively removes it from the surface. With the ability to throw snow up to 40 feet away, the Husqvarna 1130 SBEXP ensures that you can clear driveways, sidewalks, and patios without worrying about where the snow will land. The auger design also reduces clogging, ensuring uninterrupted performance during use.

Equipped with the innovative Hydrostatic transmission, the Husqvarna 1130 SBEXP offers smooth speed control, allowing the operator to adjust the pace according to the terrain or snow conditions. This feature adds to the machine’s versatility and user-friendliness, making it suitable for various applications.

Another highlight of this snow blower is its adjustable chute and deflector. This allows users to direct the snow exactly where they want it to go, enhancing maneuverability and effectiveness. The chute rotation can be easily controlled from the operator's position, giving you full command while clearing snow.

For added convenience, the Husqvarna 1130 SBEXP features LED headlights, ensuring visibility during early morning or late evening snow clearing. The model also includes heated handle grips for comfort, minimizing fatigue during prolonged use in cold weather.

With rugged tires designed for maximum traction and stability, the Husqvarna 1130 SBEXP excels on uneven surfaces, making it a reliable choice for any winter landscape. Its combination of power, convenience, and innovative technology positions the Husqvarna 1130 SBEXP as a leading choice in the snow blower category, ensuring that you can efficiently manage winter’s challenges while keeping your exterior spaces safe and accessible.
Top Page Image Contents