Husqvarna 1130 SBEXP owner manual Table of Contents

Page 3

6.When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the en- gine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the dis- charge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and work- ing.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16.Never touch a hot engine or muffler.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. Ithasbeendesigned,engineeredandmanufactured to give best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODELAND SERIAL NUMBERS WILL BE FOUND ONADECALATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity

4.0 Quarts

and Type:

Unleaded Regular only

 

 

Oil Type

SAE 30 (above 40°F)

(API SG–SL):

SAE 5W-30 or 10W-30 (0° to +40°F)

 

SAE 0W-30 (below 0°F)

 

 

Oil Capacity:

26 Ounces

 

 

Spark Plug:

Champion RN4C (Gap: .030")

 

 

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES

2-3

PRODUCT SPECIFICATIONS

3

CUSTOMER RESPONSIBILITIES

3

WARRANTY

32

ASSEMBLY / PRE-OPERATION

5-7

OPERATION

8-14

MAINTENANCE

14-15

MAINTENANCE SCHEDULE

14

SERVICE AND ADJUSTMENTS

16-18

STORAGE

18

TROUBLESHOOTING

19

3 REPAIR PARTS

20-31

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 1130SBEXP Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Unfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerMeets A.N.S.I. Safety Requirements Stopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigScraper BAR Before Starting the EngineIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingBefore Each USE Maintenance➀ SAE 30 Motor Oil ➁ See Engine in Maintenance section General RecommendationsCleaning Snow ThrowerEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts 532 17 KEY Part DescriptionControl Panel / Discharge Chute KEY Part Description Handles Repair Parts Drive Repair Parts Chassis / Engine / Pulleys KEY Part Description Repair Parts Wheels / Decals 532 40 Wheels / DecalsSion Tmita ILD NA SON ITP Eexc 4ON ITC ES Rantywar Tementsta

1130 SBEXP specifications

The Husqvarna 1130 SBEXP is a powerful snow blower designed to tackle the challenges posed by heavy snowfall and icy conditions. With its robust construction and advanced features, it stands out as a reliable tool for both residential and commercial use.

One of the most notable features of the Husqvarna 1130 SBEXP is its impressive clearing width of 30 inches, allowing users to clear a large path quickly and efficiently. The high-performance 291cc Husqvarna engine delivers reliable power, ensuring optimal performance in even the most challenging winter conditions. This engine is designed for easy starting and operation, so users can get to work without delays.

The machine boasts a durable steel auger that not only breaks up packed snow but also effectively removes it from the surface. With the ability to throw snow up to 40 feet away, the Husqvarna 1130 SBEXP ensures that you can clear driveways, sidewalks, and patios without worrying about where the snow will land. The auger design also reduces clogging, ensuring uninterrupted performance during use.

Equipped with the innovative Hydrostatic transmission, the Husqvarna 1130 SBEXP offers smooth speed control, allowing the operator to adjust the pace according to the terrain or snow conditions. This feature adds to the machine’s versatility and user-friendliness, making it suitable for various applications.

Another highlight of this snow blower is its adjustable chute and deflector. This allows users to direct the snow exactly where they want it to go, enhancing maneuverability and effectiveness. The chute rotation can be easily controlled from the operator's position, giving you full command while clearing snow.

For added convenience, the Husqvarna 1130 SBEXP features LED headlights, ensuring visibility during early morning or late evening snow clearing. The model also includes heated handle grips for comfort, minimizing fatigue during prolonged use in cold weather.

With rugged tires designed for maximum traction and stability, the Husqvarna 1130 SBEXP excels on uneven surfaces, making it a reliable choice for any winter landscape. Its combination of power, convenience, and innovative technology positions the Husqvarna 1130 SBEXP as a leading choice in the snow blower category, ensuring that you can efficiently manage winter’s challenges while keeping your exterior spaces safe and accessible.
Top Page Image Contents