Jeep E-60 owner manual Detaching the Complete Assembly

Page 7

DETACHING THE COMPLETE ASSEMBLY

Leave control switch in lower float position and push down on the Lift Arm. Disconnect the electrical plug and slip on weather caps over both ends. Attach Crankstand to the adjustment tube in the center of the A Frame using the chained locking pin. Caution: Crankstand must be secured at all times. Adjust the Crankstand down until the bottom of stand touches the ground. Pull and twist the two rear Blue Handle Pins to disengage. Next pull and twist the two front Blue Handle Pins to disengage. If the pins do not pull easily, adjust stand up or down slightly to remove tension on the pins until they disengage. At this time the lift frame should be leaning forward slightly, at rest on the top of the Crankstand. Pull truck away.

DETACHING MOLDBOARD ASSEMBLY ONLY

Leave control switch in lower float position and push down on the Lift Arm. Disconnect hydraulic couplers and Lift Chain from Lift Arm. Attach Crankstand to the adjustment tube in the center of the A- Frame using the chained locking pin. Caution: Crankstand must be secured at all times. Adjust the Crankstand down until the bottom of stand touches the ground. Pull and twist the Yellow Handled Pins to disengage. If the pins do not pull easily, adjust stand up or down slightly to remove tension on the pins until they disengage. Pull truck away.

ATTACHING THE COMPLETE ASSEMBLY

Check that all four Blue Handle Pins are disengaged. Drive the truck up to the MDII assembly centering the hood of the truck to the lift arm to assure proper alignment with lift frame guide plates until contact is made. Once contact is made drive forward, pushing the assembly a few inches. This insures the A-Frame is square to the Clevis Frame for proper pin attachment. Adjust the Crankstand up

until the front of the truck raises slightly. The rear Blue Handle Pins should now be aligned with the rear holes on the clevis frame. Twist all Blue Handle Pins so that the small leg re-aligns with the slot, engaging the pins. The rear spring loaded pins should snap into place. Note: If pins do not lock immediately the A-Frame is not square to the Clevis Frame. Move truck slightly forward and/or adjust the Crankstand up or down until rear pins engage. Once the back pins are locked push the top of the Lift Frame towards the truck locking the front pins to the clevis frame. Remove the Crankstand from the A-frame by removing the chained locking pin. Reattach the Crankstand to the transport tube on the driver's side of the Lift Frame in the vertical, retracted position. Caution: Crankstand must be secured at all times. Reattach the one step electrical connection.

6

Image 7
Contents Snowplows Tripedge Series Table of ContentsIntroduction Get to know your Diamond Mdii Snow Plow Adjustable Tripedge Extension SpringsPage Crankstand Storage Detaching the Complete Assembly Get to know your Diamond Tripedge Snowplow Power Angling CylindersPull-Away Easy Hitch Mounting System Mdii Mounting SystemModel Tripedge SeriesModels 8.0, 8.5 II. Controls and Operating Instructions Special FeaturesTRIP-EDGE Diamond Snowplow Instructions Choice 1 Attaching Mdii Entire Mount Choice 2 Removing Mdii Moldboard Only Choice 2 Attaching Mdii Moldboard Only Over-the-Road Operation Removing Moldboard AssemblyPre-Season Maintenance General MaintenancePost-Season Summer Maintenance Testing Tips Model Condition Possible Cause Correction Troubleshooting Chart for Electric Hydraulic Power UnitsModel Condition Possible Cause Correction Preparing AREAS, USE of Guide Markers Efficient Snow Clearance Starts with PlanningKeep Snow Under Control Average Hourly Snow Clearing CAPACITIES* Table Selecting EquipmentPlow with the Storm Plan I less than 50,000 sq. ft Two Established Snow Clearance PlansPlan II over 50,000 sq.ft Snowplowing Open Areas Snowplowing Tips from the ProsParking Lots Wide Driveway Straight Line SnowplowingStacking DrivewaysClearing Trapped Areas Clearing Residential AreasMinerals and Chemicals for Ice Control Replaceable Tailgate Spreader Meyer MateInsert Hopper Spreader Reversible Cutting Edge Trip Edge AccessoriesMini and Mini JR LOW PRO Spreaders 5’ 1/2 YARD, 6’ 3/4 YARD, 7’ 1 YardFull Trip Parts Tripedge PartsTWO Meter A-FRAME EZ-GARD ELECTRO-TOUCHSNO-FLO Powder Coat TOUCH-UP Paint M1 Hydraulic FluidPage Pump Torque SpecificationsHydraulic Specifications Hydraulic Fluid CapacityHydraulic Fluid Capacity 57H ELECTRO-LIFT Power UnitsOwner Warranty Registration Card Page TWO Year Warranty