Additional Remote Control in Lieu of Cleaner

ADDITIONAL REMOTE CONTROL IN LIEU OF CLEANER:

If the system does not utilize aseparate pool cleanerpum~it is possible to use the pool cleaner relay to activate an additional remote circuit This circuit is controlled by the Spa-side Remote Control

NOTE: CLNR Program Button on the Time Master Controller will be redundant. Flag and Status Light may still be turned ON, but display is meaningless.

Adjust U1O Program Switch (located at the bottom of the printed circuit board) so that Switches #4, # 5 and # 6 are programmed ON, and Switches #1, #2, #3 and #7 are programmed OFF.

Modify low voltage wiring as follows

Disconnect black wire of blklyel pair from CLNR screw terminal on LX-10 printed circuit board, and subsitute with yellow wire from SS-100 Spa-side Remote

SPA WATERFALL CONTROL:

For systems where spa water level is higher than that of the pooh a Spa Waterfall Control (model RLY-WRFL) may be added

AUXl Button at theTime Master or an optional Remote Control switch can be used to rotate the return valve operator to SPA position while system is in POOL mode, thus creating an overflow(waterfall effect) from spa to pool This effect will ceasewhenever the system is in SPA mode.

Install RLY-WRFL in accordance with instructions provided.

ELECTRIC HEATER CONTROL:

For systems which utilize a heat pump or electric heater in lieu of a gas heater, a Relay Kit (model RLY-LX) should be added at the LX-10. Install RLY-LX in accordance with instructions provided, and plug into ELEC HTR relay socket on printed circuit board The power relay is capable of controlling a heat pump, an electric heater rated up to 3KV4 or the magnetic contactor of a larger electric heater.

FREEZE SENSOR:

A Recirculating Freeze Sensor(mode1 FPS-C) may be added to the system It protects the plumbing and equipment from possible freeze damage by running the filter pump whenever the temperature falls to approx 41'F. Install FPS-C in accordance with instructions provided

An Auxiliary Pump Freeze Sensor(mode1FPS-AUX)may also beadded to the system to activate auxiliary equipment (such as jet pump) during potential freezing conditions Install FPS-AUX in accordance with instructions provided

CUSTOM OPTIONS:

Additional custom options are also available. These options, however, require custom adjustments at the factory.

Consult Compool Corporation for details.

SAVE THESE INSTRUCTIONS

HIGH VOLTAGE WIRING:

All high voltage connections are made to terminal blocks, which are located b e hind service panel in right side compartment of LX-10 Service Center.

A high voltage wiring label is located adjacent t o terminal blocks. Knock out holes are provided on bottom of enclosure for conduit mounting.

Provide a separate circuit breaker (if possible) to power the system. Either 115VAC or 230VAC can be used System draws less than 1 amp. Runwires from circuit breaker to high voltage compartment of LX-10,and connect to top terminal blockwhich is marked "SYSTEM POWER". Install2 jumpersfor1 15V,or1 jumperfor230Vwiring, according to wiring label.

Provide independent circuit breakers(if possible) for FLTR, CLNR, and AUX 1.

Note: AUX 2,"AUX 3, and AUX 4 are optional and require additional relay kits (model RLY-LX).

Run wires from breakers to high voltage compartment of LX-10,and connect to LlNE 1 and LlNE 2 of relevant terminal blocks

Connect pumps and other high voltage equipment to LOAD 1 and LOAD2 terminals at relevant terminal blocks Each individual terminal blockcan be wired for either 115 or 230V AC. A relay allocation chart is provided inside enclosure cover for the service man'sconvenience

To reduce the risk of electric shock provide a continuous green insulated copper wire, no smaller than #12 AWG between grounding bus of LX-10 and grounding terminal of electrical supply panel

A wire connector is provided for bonding to local ground points To further reduce the risk of electric shock this connector should be bonded with a #8 AWG copper wire to any metal ladders, water pipes, or other metal within 5 feet of pool or spa

TIME MASTER:

Select a convenient location inside the house or other weather-protected area to mount Time Master Controller.

Unscrew faceplate from enclosure, and use enclosure as a template to mark and cut hole ( 8%" wide by 4%" high) in sheetrock or wall panel in^ Using the mounting clips

provided, install enclosure into wall.

Strip jacket of 6pair cable 6" to identify the twisted pairs and assure correct connections Strip insulation of each wire l/4" and connect to screw terminal in accordance with wiring dia- gram located inside enclosure.

Caution: Do not untwist pairs It is necessary to retain wires in pairs so that appropriate connec- tions can be identified

Note: For the convenience of the sewiceman

'screw terminal can be unplugged from printed circuit board without disconnecting wires Mount faceplate to enclosure.