Bel Canto Design PReProTM warranty General Operation of Unit

Page 22

General Operation of Unit

Power up unit

1.Press MASTER power button all the way in. This turns on the power and puts the unit in standby. Do not turn the unit off by pressing this button. Press the OFF button on the right of the font panel.

Turn unit on and off

1.Press any INPUT button on the front panel or on the remote. It will select the input and turn the unit on.

2.To turn the unit off press the OFF button on the front panel or the POWER button on the remote.

Mute the unit

1.Press the MUTE button on the front panel or press the MUTE button on the remote. When the system is in mute the unit will not respond to any commands except the mute command.

2.To un-mute press the MUTE button again on the front panel or the remote.

Volume control

1.Press volume up or down on the remote or front panel.

Modes

1.MUSIC 7. Press this button and the system will go into MUSIC 7 from a PCM source with no flag or analog input. It has no effect with a multi-channel digital input.

2.STEREO mode works by pressing the stereo button on the remote. When you press the stereo button it will take you out of any multi channel processing and put you into stereo mode. If it is a DOLBY Digital input it will mix down to DOLBY 2 channel.

3.SURROUND button. When you have an analog stereo 2 Ch. or PCM Input and you press the surround button, it will put the PRePro in the surround mode.

4.MODE button. This button selects between Dolby Prologic logic2: Music, Dolby Prologic logic2: Movie, DTS Neo6: Music, or DTS Neo6: Cinema as the default for 2-Channel Sources with no flags.

5.7.1 input. When you press 7.1 from front panel or remote the unit will select the DVD video input and the 7.1 audio input.

6.To put 7.1 audio in the full range mode (no filters) press MENU and press 9 to toggle full range YES or NO press SELECT when YES or NO is blinking.

Tuner

1.To select a station on the tuner press SEEK UP or DOWN until you have the desired station. Then press the desired preset button 1 through 10 round button on the remote or front panel and hold down until the sound comes back. Release the button and your preset is set.

2.After you have set all your favorite sta- tions use the preset buttons to select sta- tions.

3.The tuner should use a 75 ohm antenna for FM, and an AM antenna.

Note: The seek is set very sensitive so you can get weak stations, but there will be noise on weak stations.

Main Zone Triggers

1.The PRePro has 2 main zone triggers. One is 12-Volt 200 mA and the other is a dry contact relay at 1 Amp. The relay delay is 5 seconds before the main zone is turned on. When main zone is turned off, 12 Volts is off and the relay opens.

Infra Red Input

1.IR input allows a repeater or blaster input from Zone 2 or any other IR input.

Replacing the AC Power Fuse

1.Turn the unit off.

2.Disconnect the AC power cord.

3.Slide open the fuse drawer completely.

4.Replace with 250V 1 Amp Slo-blo fuse.

© 2002/2003 bel canto design, Ltd.

Page 22

PRePro User’s Guide rev1103

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Users Guide and Warranty Information PReProCongratulations General PrecautionsProduct Warranty Information UnpackingQuick Setup Placement GuidelinesAC Connecti AC Connection and Power RecommendationsQuick Setup Speaker Size Speaker SizeSpeaker Distance Loudspeaker Setup Loudspeaker Size and Subwoofer Setup Tuner Settings Input Audio AssignmentBass Trim Calibration Press Exit to get back to the Main MenuCompression Status DisplayReset to Defaults DVD Audio Full RangeAdvanced Setup Advanced Setup/Input Name ChangeHardware Setup Video Monitor Connection Multi-Channel Output Connection Digital Source Set-up & Connection To Change Input Assignment To Change Input Assignment NameAnalog Source Set-up & Connection To Change Input Assignment To Analog Setting up Zone Zone 2 TriggerGeneral Operation of Unit This button toggles Mutes on and off This button toggles TFT display on and off AC Power Fuse Holder Rear Panel ConnectionsRemote Control Controls and FunctionsLearning a New Command Remote Control Learning ModeStep Erasing All the Learned Commands in One Device Mode Step Erasing a Learned Command From a Button StepErasing All of the Learned Commands in All Device Modes Volume Punch Through Programming a Macro SequenceExample for Programming a Macro Sequence Listening Mode Definitions Listening ModesPRePro User’s Guide rev1103 Troubleshooting Guide Trouble Shooting the BasicsSpecifications AUDIO/VIDEO Section

PReProTM specifications

Bel Canto Design PReProTM is a distinguished preamplifier that has garnered attention for its innovative features and exceptional sound quality. This high-performance audio component stands as a testament to Bel Canto's commitment to enhancing the listening experience through expert engineering and design.

One of the defining characteristics of the PReProTM is its cutting-edge digital processing capabilities. It employs advanced digital signal processing (DSP) technology that allows for precise control over the audio signal. This processing enables the PReProTM to deliver crystal-clear sound reproduction across a wide frequency range while minimizing distortion. The integration of DSP not only enhances playback quality but also provides users with customizable options for tailoring their audio experience.

Connectivity is another standout feature of the PReProTM. It offers a comprehensive array of inputs, including a selection of digital inputs such as USB, coaxial, and optical, facilitating seamless integration with various audio sources. Additionally, the preamplifier includes multiple analog inputs, making it versatile enough to accommodate both modern digital devices and traditional analog components. This flexibility ensures that users can connect all their audio equipment with ease.

The PReProTM is designed with an emphasis on user-friendly operation. It features an intuitive interface, allowing users to navigate settings and modes effortlessly. The clear display provides vital information about the selected input, volume levels, and audio processing settings, ensuring that the user remains informed and in control of their listening experience.

Moreover, the PReProTM boasts high-quality components, including meticulously selected capacitors, resistors, and a power supply designed to reduce noise and improve signal integrity. This attention to detail contributes to its ability to deliver a rich, immersive soundstage, allowing listeners to experience music as it was intended by the artists.

Another notable attribute of the PReProTM is its robust build quality. Constructed with a combination of durable materials and sophisticated engineering, the preamplifier is not only reliable but also designed to minimize resonance and interference. This design principle helps maintain the integrity of the audio signal, resulting in a more accurate and enjoyable listening experience.

In conclusion, the Bel Canto Design PReProTM is an exceptional preamplifier that brings together advanced technologies, versatile connectivity options, user-friendly operation, high-quality components, and a robust build. These features make it a prime choice for audiophiles and casual listeners alike, enhancing the enjoyment of music and audio in any setting. Whether integrating with a sophisticated home audio system or serving as the centerpiece of a high-end setup, the PReProTM delivers performance that elevates the listening experience to new heights.
Top Page Image Contents