ViewSonic PJD7400 Connecting a Component Video source device, Connecting an S-Video source device

Page 23

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output sockets available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a D-Sub type connector) to the COMPUTER IN 1 or COMPUTER IN 2 socket on the projector.

• If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

•

VGA-Component adapter

(ViewSonic P/N: CB-00008906)

 

Connecting an S-Video source device

Examine your Video source device to determine if it has an unused S-Video output socket available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video source device:

1.Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.

2.Connect the other end of the S-Video cable to the S-VIDEOsocket on the projector.

• If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

•If you have already made a Component Video connection between the projector and this S-Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video source devices" on page 18 for details.

18

Page 22 Page 24
Image 23
Page 22 Page 24
Contents User Guide Compliance Information Important Safety Instructions Declaration of RoHS Compliance Copyright Information Table of contents Safety Instructions Important safety instructionsSafety instructions for ceiling mounting of the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side Projector Controls and functionsRemote control Operating the Laser pointer Using the remote mouse controlReplacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorPJD7382/PJD7400 Projection dimensionsPJD7400 PJD7400w VGA DVI ConnectionTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorLeast video quality Connecting Video source devicesBest video quality Better video qualityTo connect the projector to an S-Video source device Connecting a Component Video source deviceConnecting an S-Video source device To connect the projector to a Component Video source deviceAbout the microphone input Connecting a composite Video source devicePlaying sound through the projector To connect the projector to a composite Video source deviceSignal Parameter Min Type Max Starting up the projector OperationSee Timing chart on page 64 for details System Setup Advanced Using the menusSystem Setup Basic If you forget the password Utilizing the password functionSetting a password Disabling the password function Entering the password recall procedureChanging the password Switching input signal Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Correcting keystone Fine-tuning the image claritySelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Video input signals S-Video, Video, D-Sub / Comp /2 YPbPr Selecting a picture modePicture modes for different types of signals PC input signals D-Sub / Comp /2 analog RGBAdjusting Brightness Using Screen ColorFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessColor Management To adjust the settingsTo cancel the timer, perform the following steps Setting the presentation timerLocking control keys Hiding the imageOperating in a high altitude environment To activate the High Altitude ModeFreezing the image Creating your own startup screen If you are in a non-DHCP environment Configuring the LAN Control SettingsControlling the projector through a LAN environment If you are in a Dhcp environmentControlling the projector through a web browser e-Con- trol Category Item Input Length Maximum Number Characters Press Exit to go back to the remote network operation Active VGA Out Using the projector in standby modePower Saving MicrophoneShutting down the projector Picture Contrast Menu operationMenu system System Setup Basic DCR AdvancedDescription of each menu Reference Color ModeTemperature SettingsProjector Auto PowerBlank Timer LanguageCaption AudioMenu ClosedPresentation TimerReset All LampCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Ensure the handle is fully laid flat and locked in place Resetting the lamp timer Light Status & Description IndicatorsCause Remedy TroubleshootingProjector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputDisclaimer Copyright informationCopyright Pin assignment for this two end RS232 command tableAppendix IR control tableInterface OFF 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07 Svideo Write Reset Lamp Customer Support Limited Warranty Effect of state law Sales outside the U.S.A. and Canada Mexico Limited Warranty Número Gratis DE Asistencia Técnica Para Todo México

PJD7400, PJD7400W, PJD7382 specifications

The ViewSonic PJD7400, PJD7400W, and PJD7382 projectors are designed to meet the diverse needs of both educational and professional environments, delivering exceptional performance and versatility. These projectors offer advanced features that enhance the viewing experience while ensuring robust connectivity and usability.

Starting with the PJD7400, this model boasts a bright 3200 lumens output, which ensures vibrant images even in well-lit environments. It has a high resolution of 1024x768 (XGA), making it suitable for displaying presentations, videos, and images with clarity. One of its standout features is the SuperColor technology, which provides a wide color gamut for accurate color reproduction. Additionally, the PJD7400 comes equipped with a 1.96-2.16 throw ratio, allowing for flexible installation options depending on room size.

The PJD7400W takes things a step further by offering a higher resolution of 1280x800 (WXGA). This model is perfect for widescreen content, providing enhanced detail and quality. With its 3200 lumens brightness, the PJD7400W can handle various lighting conditions, making it an excellent choice for classrooms and conference rooms. Like the PJD7400, it also features SuperColor technology, ensuring lifelike colors that captivate audiences. The PJD7400W has a low throw ratio and vertical keystone correction, which simplifies setup and alignment.

The PJD7382 serves as a more premium option within this lineup, featuring full 1080p resolution (1920x1080) for superior image quality. With a brightness level of 3500 lumens, it stands out as the brightest among the trio, ensuring clear visuals even in bright conditions. This model also incorporates advanced connectivity options, including HDMI, VGA, and USB ports, allowing for easy integration with a range of devices. The PJD7382 includes a 1.1x optical zoom lens, giving users further flexibility in adjusting image size without moving the projector.

Overall, the ViewSonic PJD7400, PJD7400W, and PJD7382 projectors provide exceptional performance features, making them ideal for a variety of settings. Their brightness, resolution capabilities, and advanced technologies like SuperColor ensure that users can expect high-quality presentations and images. Whether for educational purposes, business meetings, or home entertainment, these projectors deliver reliable, versatile solutions.
Top Page Image Contents