ViewSonic PJD7382, PJD7400W warranty Operation, Starting up the projector

Page 26

Operation

Starting up the projector

1.Plug the power cord into the projector and into a

wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator light on the projector flashes blue after power has been applied.

2.Remove the lens cap. If it is closed, it could become deformed due to the heat produced by

the projection lamp.

3.Press II POWER on the projector or remote control to start the projector. The POWER indicator light stays blue when the projector is on.

(If necessary) Rotate the focus ring to adjust the image clearness.

• If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp.

•To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning it off.

4.If the projector is activated for the first time, select your OSD language following the on- screen instructions.

5.Switch all of the connected equipment on.

PJD7382

PJD7400/PJD7400w

21

Page 25 Page 27
Image 26
Page 25 Page 27
Contents User Guide Compliance Information Important Safety Instructions Declaration of RoHS Compliance Copyright Information Table of contents Important safety instructions Safety InstructionsSafety instructions for ceiling mounting of the projector Projector features IntroductionShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions ProjectorRemote control Using the remote mouse control Operating the Laser pointerRemote control effective range Replacing the remote control batteriesPositioning your projector Choosing a locationProjection dimensions PJD7382/PJD7400PJD7400 PJD7400w Connection VGA DVIConnecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerBetter video quality Connecting Video source devicesBest video quality Least video qualityTo connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source devicePlaying sound through the projector About the microphone inputSignal Parameter Min Type Max Operation Starting up the projectorSee Timing chart on page 64 for details System Setup Advanced Using the menusSystem Setup Basic If you forget the password Utilizing the password functionSetting a password Disabling the password function Entering the password recall procedureChanging the password Switching input signal Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarity Correcting keystoneMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio PC input signals D-Sub / Comp /2 analog RGB Selecting a picture modePicture modes for different types of signals Video input signals S-Video, Video, D-Sub / Comp /2 YPbPrSetting the User 1/User 2 mode Using Screen ColorFine-tuning the image quality in user modes Adjusting BrightnessAdjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Brilliant ColorTo adjust the settings Color ManagementSetting the presentation timer To cancel the timer, perform the following stepsHiding the image Locking control keysOperating in a high altitude environment To activate the High Altitude ModeFreezing the image Creating your own startup screen If you are in a Dhcp environment Configuring the LAN Control SettingsControlling the projector through a LAN environment If you are in a non-DHCP environmentControlling the projector through a web browser e-Con- trol Category Item Input Length Maximum Number Characters Press Exit to go back to the remote network operation Microphone Using the projector in standby modePower Saving Active VGA OutShutting down the projector Picture Contrast Menu operationMenu system System Setup Basic Advanced DCRDescription of each menu Settings Color ModeTemperature ReferenceLanguage Auto PowerBlank Timer ProjectorClosed AudioMenu CaptionLamp TimerReset All PresentationMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Ensure the handle is fully laid flat and locked in place Resetting the lamp timer Indicators Light Status & DescriptionTroubleshooting Cause RemedySpecifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsDisclaimer Copyright informationCopyright IR control table RS232 command tableAppendix Pin assignment for this two endInterface OFF 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07 Svideo Write Reset Lamp Customer Support Limited Warranty Effect of state law Sales outside the U.S.A. and Canada Mexico Limited Warranty Número Gratis DE Asistencia Técnica Para Todo México

PJD7400, PJD7400W, PJD7382 specifications

The ViewSonic PJD7400, PJD7400W, and PJD7382 projectors are designed to meet the diverse needs of both educational and professional environments, delivering exceptional performance and versatility. These projectors offer advanced features that enhance the viewing experience while ensuring robust connectivity and usability.

Starting with the PJD7400, this model boasts a bright 3200 lumens output, which ensures vibrant images even in well-lit environments. It has a high resolution of 1024x768 (XGA), making it suitable for displaying presentations, videos, and images with clarity. One of its standout features is the SuperColor technology, which provides a wide color gamut for accurate color reproduction. Additionally, the PJD7400 comes equipped with a 1.96-2.16 throw ratio, allowing for flexible installation options depending on room size.

The PJD7400W takes things a step further by offering a higher resolution of 1280x800 (WXGA). This model is perfect for widescreen content, providing enhanced detail and quality. With its 3200 lumens brightness, the PJD7400W can handle various lighting conditions, making it an excellent choice for classrooms and conference rooms. Like the PJD7400, it also features SuperColor technology, ensuring lifelike colors that captivate audiences. The PJD7400W has a low throw ratio and vertical keystone correction, which simplifies setup and alignment.

The PJD7382 serves as a more premium option within this lineup, featuring full 1080p resolution (1920x1080) for superior image quality. With a brightness level of 3500 lumens, it stands out as the brightest among the trio, ensuring clear visuals even in bright conditions. This model also incorporates advanced connectivity options, including HDMI, VGA, and USB ports, allowing for easy integration with a range of devices. The PJD7382 includes a 1.1x optical zoom lens, giving users further flexibility in adjusting image size without moving the projector.

Overall, the ViewSonic PJD7400, PJD7400W, and PJD7382 projectors provide exceptional performance features, making them ideal for a variety of settings. Their brightness, resolution capabilities, and advanced technologies like SuperColor ensure that users can expect high-quality presentations and images. Whether for educational purposes, business meetings, or home entertainment, these projectors deliver reliable, versatile solutions.
Top Page Image Contents