ViewSonic PJD5533W, PJD5134 Replacing the lamp, Remove and dispose of the lamp protection film

Page 58

Replacing the lamp

To prepare a new lamp, contact your dealer and tell the lamp type number.

Type number: RLC-078 (PJD5132/PJD5232L/PJD5134/PJD5234L)

Type number: RLC-085 (PJD5533w)

WARNING

Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org

•Be careful of broken glass when replacing the lamp.

•Please wear eye protection and gloves when performing overhead installation.

•To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp.

•To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.

•To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces. Before replacing the lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp edges in the lamp compartment. Wash hands after lamp replacement.

•Only ViewSonic certified lamps are tested with this projector. Use of other lamps may cause electrical shock and fire.

1.Turn the power off and disconnect the projector from the wall socket. If the lamp

is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2. Loosen the screws that secure the lamp cover on the both sides of the projector until the lamp cover loosens.

3.Remove the lamp cover from the projector.

WARNING

• Do not turn the power on with the lamp cover removed.

• Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

Remove and dispose of the lamp protection film.

53

Page 57 Page 59
Image 58
Page 57 Page 59
Contents PJD5132/PJD5232L/PJD5134 PJD5234L/PJD5533w DLP Projector Compliance Information Important Safety Instructions Declaration of RoHS2 Compliance Copyright Information Table of contents Important safety instructions Safety InstructionsSafety instructions for ceiling mounting of the projector Projector features IntroductionShipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions ProjectorRemote control Timer Color ModeVolume keys + MagnifyUsing the remote mouse control Set the input signal to D-Sub / Comp , D-Sub / Comp or HdmiReplacing the remote control batteries Front Table Positioning your projectorChoosing a location Front CeilingPJD5132/PJD5232L/PJD5134/PJD5234L Projection dimensionsImage on a 43 screen PJD5533w Connection Connecting a monitor Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerBest video quality Connecting Video source devicesConnecting audio Better video qualityTo connect the projector to an Hdmi device Connecting an Hdmi deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUse / to highlight the System Setting Basic menu Using the menusBelow is the overview of the OSD menu Setting a password Utilizing the password functionIf you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Switching input signal Changing Hdmi input settingsAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityTo correct keystoning at the bottom of the image Magnifying and searching for detailsCorrecting keystone To navigate the pictureSelecting the aspect ratio About the aspect ratio Picture PC input signals D-Sub / Comp /2 analog RGB Selecting a picture modePicture modes for different types of signals Optimizing the imageSetting the User 1/User 2 mode Using Screen ColorFine-tuning the image quality in user modes Go to the Picture Color Mode menuAdjusting Color Adjusting BrightnessAdjusting Contrast Adjusting TintColor Management About color temperaturesTo adjust the settings T4 Makes images appear reddish whiteSetting the presentation timer To cancel the timer, perform the following stepsFreezing the image Hiding the imageLocking control keys Operating in a high altitude environmentTo highlight High Altitude Mode Using the CEC functionUsing the 3D functions Go to the System Setting Basic CEC menuUsing the projector in standby mode Power SavingShutting down the projector Quick Power OffActive Audio Out Menu operation Menu systemSystem System Setting Advanced Color System Description of each menu Save Settings Color ModeTemperature ReferenceSearch TimerQuick Auto Hdmi FormatLanguage Auto PowerSettings ProjectorClosed Audio Settings MuteHigh Altitude CaptionSecurity Reset SettingsPresentation RemoteMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Remove and dispose of the lamp protection filmLoosen the screw that secures the lamp Ensure the handle is fully laid flat and locked in placeRestart the projector Resetting the lamp timerAfter the startup logo, open the On-Screen Display OSD menu Light Status & Description IndicatorsPower events Lamp eventsTroubleshooting Cause RemedySpecifications Projector specificationsEnvironmental Requirements Output terminalControl terminal RS-232 serial control Pin xCeiling mount installation DimensionsMm W x 84.4 mm H x 221 mm D Excluding extrusions Timing chart Supported timing for PC inputSupported timing for Component-YPbPrinput Copyright information CopyrightIR control table AppendixCode a Code B RS232 command tablePin assignment for this two end RS232 command table InterfaceFront Table Color Hdmi Range 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 Customer Support Limited Warranty How to get service Mexico Limited Warranty VSCTEMP2006

PJD5533W, PJD5134 specifications

The ViewSonic PJD5134 and PJD5533W projectors are impressive options for both home and office environments, delivering high-quality visual performance with practical features that cater to various projection needs.

The ViewSonic PJD5134 is particularly renowned for its portability and versatility, suitable for meeting rooms, classrooms, and even home entertainment. It boasts an SVGA resolution of 800x600 pixels, making it ideal for standard presentations and videos. With a brightness of 3,000 ANSI lumens, the PJD5134 ensures clear visibility in various lighting conditions. The lamp life of up to 10,000 hours further enhances its appeal, reducing maintenance costs and increasing convenience.

One of the standout features of the PJD5134 is its extensive connectivity options. It includes HDMI, VGA, and composite video inputs, allowing users to connect a variety of devices, including laptops, tablets, and DVD players. The integrated speaker provides adequate audio output for small to mid-sized rooms without the need for additional sound equipment. Additionally, the projector's lightweight design and compact size make it easy to transport, making it an excellent choice for on-the-go presentations.

On the other hand, the ViewSonic PJD5533W is designed for users seeking enhanced resolution and superior image quality. This projector features a WXGA resolution of 1280x800 pixels, providing a wider aspect ratio suitable for displaying HD content and more detailed images. With a brightness of 3,500 ANSI lumens, the PJD5533W excels in brightly lit environments, ensuring that presentations remain vivid and engaging.

The PJD5533W incorporates advanced DLP technology, known for its excellent color accuracy and sharpness. It also supports a 3D-ready feature, allowing users to engage audiences with immersive content. This projector offers multiple connectivity options, including HDMI, making it easy to connect to modern devices. Furthermore, the built-in speaker and high durability make the PJD5533W a robust solution for both educational and professional settings.

In terms of user-friendly features, both models come equipped with eco-friendly functionalities, such as an energy-saving mode that reduces power consumption. This not only extends the lifespan of the lamp but also contributes to lower overall operating costs.

In summary, the ViewSonic PJD5134 and PJD5533W are excellent projectors that cater to different user needs, from basic presentations to high-quality image projection. With their compelling features, robust performance, and reliable technologies, they stand out as valuable tools for any professional or educational setting.
Top Page Image Contents