ViewSonic PJD5134, PJD5533W warranty Disabling the password function

Page 29

Disabling the password function

To disable password protection, go back to the SYSTEM SETTING: ADVANCED > Security Settings > Power On Lock menu after opening the OSD menu system. Select Off

by pressing / . The message 'INPUT PASSWORD' is displayed. Enter the current password.

•If the password is correct, the OSD menu returns to the Security Settings page with 'Off' shown in the row of Power On Lock. You will not have to enter the password next time you turn on the projector.

•If the password is incorrect, the password error message is displayed lasting for three seconds, and the message 'INPUT PASSWORD' is displayed for your retry. You can press MENU/EXIT on the projector or Exit on the remote control to cancel the change or try another password.

Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

24

Page 28 Page 30
Image 29
Page 28 Page 30
Contents PJD5132/PJD5232L/PJD5134 PJD5234L/PJD5533w DLP Projector Compliance Information Important Safety Instructions Declaration of RoHS2 Compliance Copyright Information Table of contents Safety Instructions Important safety instructionsSafety instructions for ceiling mounting of the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side Projector Controls and functionsRemote control Volume keys + Color ModeTimer MagnifySet the input signal to D-Sub / Comp , D-Sub / Comp or Hdmi Using the remote mouse controlReplacing the remote control batteries Choosing a location Positioning your projectorFront Table Front CeilingImage on a 43 screen Projection dimensionsPJD5132/PJD5232L/PJD5134/PJD5234L PJD5533w Connection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting audio Connecting Video source devicesBest video quality Better video qualityConnecting a Component Video source device Connecting an Hdmi deviceTo connect the projector to an Hdmi device To connect the projector to a Component Video source deviceConnecting a composite Video source device Connecting an S-Video source deviceTo connect the projector to an S-Video source device To connect the projector to a composite Video source deviceStarting up the projector OperationBelow is the overview of the OSD menu Using the menusUse / to highlight the System Setting Basic menu If you forget the password Utilizing the password functionSetting a password Changing the password Entering the password recall procedureDisabling the password function Changing Hdmi input settings Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Magnifying and searching for detailsTo correct keystoning at the bottom of the image To navigate the pictureSelecting the aspect ratio About the aspect ratio Picture Picture modes for different types of signals Selecting a picture modePC input signals D-Sub / Comp /2 analog RGB Optimizing the imageFine-tuning the image quality in user modes Using Screen ColorSetting the User 1/User 2 mode Go to the Picture Color Mode menuAdjusting Contrast Adjusting BrightnessAdjusting Color Adjusting TintTo adjust the settings About color temperaturesColor Management T4 Makes images appear reddish whiteTo cancel the timer, perform the following steps Setting the presentation timerLocking control keys Hiding the imageFreezing the image Operating in a high altitude environmentUsing the 3D functions Using the CEC functionTo highlight High Altitude Mode Go to the System Setting Basic CEC menuPower Saving Using the projector in standby modeActive Audio Out Quick Power OffShutting down the projector Menu system Menu operationSystem System Setting Advanced Color System Description of each menu Temperature Color ModeSave Settings ReferenceQuick Auto TimerSearch Hdmi FormatSettings Auto PowerLanguage ProjectorHigh Altitude Audio Settings MuteClosed CaptionPresentation Reset SettingsSecurity RemoteCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampRemove and dispose of the lamp protection film Replacing the lampEnsure the handle is fully laid flat and locked in place Loosen the screw that secures the lampAfter the startup logo, open the On-Screen Display OSD menu Resetting the lamp timerRestart the projector Power events IndicatorsLight Status & Description Lamp eventsCause Remedy TroubleshootingProjector specifications SpecificationsControl terminal Output terminalEnvironmental Requirements RS-232 serial control Pin xMm W x 84.4 mm H x 221 mm D Excluding extrusions DimensionsCeiling mount installation Supported timing for PC input Timing chartSupported timing for Component-YPbPrinput Copyright Copyright informationCode a AppendixIR control table Pin assignment for this two end RS232 command tableCode B Interface RS232 command tableFront Table Color Hdmi Range 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 Customer Support Limited Warranty How to get service Mexico Limited Warranty VSCTEMP2006

PJD5533W, PJD5134 specifications

The ViewSonic PJD5134 and PJD5533W projectors are impressive options for both home and office environments, delivering high-quality visual performance with practical features that cater to various projection needs.

The ViewSonic PJD5134 is particularly renowned for its portability and versatility, suitable for meeting rooms, classrooms, and even home entertainment. It boasts an SVGA resolution of 800x600 pixels, making it ideal for standard presentations and videos. With a brightness of 3,000 ANSI lumens, the PJD5134 ensures clear visibility in various lighting conditions. The lamp life of up to 10,000 hours further enhances its appeal, reducing maintenance costs and increasing convenience.

One of the standout features of the PJD5134 is its extensive connectivity options. It includes HDMI, VGA, and composite video inputs, allowing users to connect a variety of devices, including laptops, tablets, and DVD players. The integrated speaker provides adequate audio output for small to mid-sized rooms without the need for additional sound equipment. Additionally, the projector's lightweight design and compact size make it easy to transport, making it an excellent choice for on-the-go presentations.

On the other hand, the ViewSonic PJD5533W is designed for users seeking enhanced resolution and superior image quality. This projector features a WXGA resolution of 1280x800 pixels, providing a wider aspect ratio suitable for displaying HD content and more detailed images. With a brightness of 3,500 ANSI lumens, the PJD5533W excels in brightly lit environments, ensuring that presentations remain vivid and engaging.

The PJD5533W incorporates advanced DLP technology, known for its excellent color accuracy and sharpness. It also supports a 3D-ready feature, allowing users to engage audiences with immersive content. This projector offers multiple connectivity options, including HDMI, making it easy to connect to modern devices. Furthermore, the built-in speaker and high durability make the PJD5533W a robust solution for both educational and professional settings.

In terms of user-friendly features, both models come equipped with eco-friendly functionalities, such as an energy-saving mode that reduces power consumption. This not only extends the lifespan of the lamp but also contributes to lower overall operating costs.

In summary, the ViewSonic PJD5134 and PJD5533W are excellent projectors that cater to different user needs, from basic presentations to high-quality image projection. With their compelling features, robust performance, and reliable technologies, they stand out as valuable tools for any professional or educational setting.
Top Page Image Contents