ViewSonic PJD5134, PJD5533W warranty Supported timing for Component-YPbPrinput

Page 67

Supported timing for Component-YPbPrinput

Signal Format

Horizontal Frequency

Vertical Frequency (Hz)

(kHz)

 

 

480i(525i)@60Hz

15.73

59.94

480p(525p)@60Hz

31.47

59.94

576i(625i)@50Hz

15.63

50.00

576p(625p)@50Hz

31.25

50.00

720p(750p)@60Hz

45.00

60.00

720p(750p)@50Hz

37.50

50.00

1080i(1125i)@60Hz

33.75

60.00

1080i(1125i)@50Hz

28.13

50.00

1080P@60Hz

67.5

60

1080P@50Hz

56.25

50

Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration.

Supported timing for Video and S-Video inputs

Video mode

Horizontal

Vertical Frequency

Color sub-carrier

Frequency (kHz)

(Hz)

Frequency (MHz)

 

NTSC

15.73

60

3.58

PAL

15.63

50

4.43

SECAM

15.63

50

4.25 or 4.41

PAL-M

15.73

60

3.58

PAL-N

15.63

50

3.58

PAL-60

15.73

60

4.43

NTSC4.43

15.73

60

4.43

62

Image 67
Contents PJD5132/PJD5232L/PJD5134 PJD5234L/PJD5533w DLP Projector Compliance Information Important Safety Instructions Declaration of RoHS2 Compliance Copyright Information Table of contents Safety Instructions Important safety instructionsSafety instructions for ceiling mounting of the projector Introduction Projector featuresShipping contents Front/upper side Projector exterior viewRear/lower side Projector Controls and functionsRemote control Magnify Color ModeVolume keys + TimerSet the input signal to D-Sub / Comp , D-Sub / Comp or Hdmi Using the remote mouse controlReplacing the remote control batteries Front Ceiling Positioning your projectorChoosing a location Front TablePJD5132/PJD5232L/PJD5134/PJD5234L Projection dimensionsImage on a 43 screen PJD5533w Connection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorBetter video quality Connecting Video source devicesConnecting audio Best video qualityTo connect the projector to a Component Video source device Connecting an Hdmi deviceConnecting a Component Video source device To connect the projector to an Hdmi deviceTo connect the projector to a composite Video source device Connecting an S-Video source deviceConnecting a composite Video source device To connect the projector to an S-Video source deviceStarting up the projector OperationUse / to highlight the System Setting Basic menu Using the menusBelow is the overview of the OSD menu Setting a password Utilizing the password functionIf you forget the password Changing the password Entering the password recall procedureDisabling the password function Changing Hdmi input settings Switching input signalFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageTo navigate the picture Magnifying and searching for detailsCorrecting keystone To correct keystoning at the bottom of the imageSelecting the aspect ratio About the aspect ratio Picture Optimizing the image Selecting a picture modePicture modes for different types of signals PC input signals D-Sub / Comp /2 analog RGBGo to the Picture Color Mode menu Using Screen ColorFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Tint Adjusting BrightnessAdjusting Contrast Adjusting ColorT4 Makes images appear reddish white About color temperaturesTo adjust the settings Color ManagementTo cancel the timer, perform the following steps Setting the presentation timerOperating in a high altitude environment Hiding the imageLocking control keys Freezing the imageGo to the System Setting Basic CEC menu Using the CEC functionUsing the 3D functions To highlight High Altitude ModePower Saving Using the projector in standby modeShutting down the projector Quick Power OffActive Audio Out Menu system Menu operationSystem System Setting Advanced Color System Description of each menu Reference Color ModeTemperature Save SettingsHdmi Format TimerQuick Auto SearchProjector Auto PowerSettings LanguageCaption Audio Settings MuteHigh Altitude ClosedRemote Reset SettingsPresentation SecurityCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampRemove and dispose of the lamp protection film Replacing the lampEnsure the handle is fully laid flat and locked in place Loosen the screw that secures the lampRestart the projector Resetting the lamp timerAfter the startup logo, open the On-Screen Display OSD menu Lamp events IndicatorsPower events Light Status & DescriptionCause Remedy TroubleshootingProjector specifications SpecificationsRS-232 serial control Pin x Output terminalControl terminal Environmental RequirementsCeiling mount installation DimensionsMm W x 84.4 mm H x 221 mm D Excluding extrusions Supported timing for PC input Timing chartSupported timing for Component-YPbPrinput Copyright Copyright informationIR control table AppendixCode a Code B RS232 command tablePin assignment for this two end Interface RS232 command tableFront Table Color Hdmi Range 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 Customer Support Limited Warranty How to get service Mexico Limited Warranty VSCTEMP2006

PJD5533W, PJD5134 specifications

The ViewSonic PJD5134 and PJD5533W projectors are impressive options for both home and office environments, delivering high-quality visual performance with practical features that cater to various projection needs.

The ViewSonic PJD5134 is particularly renowned for its portability and versatility, suitable for meeting rooms, classrooms, and even home entertainment. It boasts an SVGA resolution of 800x600 pixels, making it ideal for standard presentations and videos. With a brightness of 3,000 ANSI lumens, the PJD5134 ensures clear visibility in various lighting conditions. The lamp life of up to 10,000 hours further enhances its appeal, reducing maintenance costs and increasing convenience.

One of the standout features of the PJD5134 is its extensive connectivity options. It includes HDMI, VGA, and composite video inputs, allowing users to connect a variety of devices, including laptops, tablets, and DVD players. The integrated speaker provides adequate audio output for small to mid-sized rooms without the need for additional sound equipment. Additionally, the projector's lightweight design and compact size make it easy to transport, making it an excellent choice for on-the-go presentations.

On the other hand, the ViewSonic PJD5533W is designed for users seeking enhanced resolution and superior image quality. This projector features a WXGA resolution of 1280x800 pixels, providing a wider aspect ratio suitable for displaying HD content and more detailed images. With a brightness of 3,500 ANSI lumens, the PJD5533W excels in brightly lit environments, ensuring that presentations remain vivid and engaging.

The PJD5533W incorporates advanced DLP technology, known for its excellent color accuracy and sharpness. It also supports a 3D-ready feature, allowing users to engage audiences with immersive content. This projector offers multiple connectivity options, including HDMI, making it easy to connect to modern devices. Furthermore, the built-in speaker and high durability make the PJD5533W a robust solution for both educational and professional settings.

In terms of user-friendly features, both models come equipped with eco-friendly functionalities, such as an energy-saving mode that reduces power consumption. This not only extends the lifespan of the lamp but also contributes to lower overall operating costs.

In summary, the ViewSonic PJD5134 and PJD5533W are excellent projectors that cater to different user needs, from basic presentations to high-quality image projection. With their compelling features, robust performance, and reliable technologies, they stand out as valuable tools for any professional or educational setting.