Eiki LC-SB21 owner manual Connecting the AC Power Cord, For the U.S.A. and Canada, 200 240 V AC

Page 16

Installation

Connecting the AC Power Cord

This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system.

Consult your authorized dealer or service station if you are not sure of the type of power being supplied.

Connect the projector with all peripheral equipment before turning the projector on. (See page 17-19 for connection.)

CAUTION

For safety, unplug AC power cord when the projector is not in use. When this projector is connected to an outlet with AC power cord, it is in Stand-by mode and consumes a little electric power.

Connect AC power cord (supplied) to the projector.

The AC outlet must be near this equipment and must be easily accessible.

NOTE ON THE POWER CORD

The AC Power Cord must meet the requirement of the country where you use the projector. Confirm the AC plug type with the chart below. The proper AC Power Cord must be used. If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.

Projector side		AC Outlet side


	For the U.S.A. and Canada				For Continental Europe


		Ground

To the POWER CORD
To the POWER CORD		To the AC Outlet.
CONNECTOR on the		To the AC Outlet.
CONNECTOR on the		(120 V AC)		To the AC Outlet.
projector.				(200 - 240 V AC)
				(200 - 240 V AC)

16

Image 16

Contents Model LC-SB21 Features and Design Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandAir Circulation Installing the Projector in Proper PositionMoving the Projector Compliance Federal Communication Commission NoticeFront Part Names and FunctionsBack Bottom Rear Terminal Part Names and FunctionsTop Control Remote Control @1 !3Laser Pointer Function Pointer FunctionWireless Mouse Operation Operating RangePart Names FunctionsRemote Control Code Remote Control Battery InstallationButton. The code switches sequentially for one pressing With holding down the Menu button, press the ImageAdjustable Feet InstallationPositioning the Projector For the U.S.A. and Canada Connecting the AC Power Cord200 240 V AC Connecting to a Computer InstallationConnecting to Video Equipment CableConnecting to Component Video Equipment Monitor OUTWhat is PIN code? Basic OperationTurning On the Projector Enter a PIN codeTurning Off the Projector Basic OperationHow to Operate the On-Screen Menu Remote ControlOn-Screen Menu Top ControlMenu Bar Basic OperationZoom and Focus Adjustment Auto Setup FunctionKeystone Adjustment Picture Freeze FunctionNo Show Function BasicTimer Function Sound AdjustmentVolume MuteInput Source Selection Computer InputComputer Input Computer System Selection AutoMode PC System MenuAuto PC Adjustment PC Adjust MenuTo store adjustment parameters Auto PC AdjManual PC Adjustment Reset Mode freeDisplay area Display area HImage Level Selection Image Level Adjustment Screen Size Adjustment Video Input Input Source Selection Video, S-VideoVideo Input Input button Video Computer Video buttonInput Source Selection Component, RGB Scart 21-Pin Input button Computer Video Computer buttonVideo System Selection AutoAV System Menu Video or S-Video AV System Menu ComponentImage1~4 CinemaImage button Dynamic Standard Cinema BlackboardGreen Color TintProgressive FilmProvides image at a normal video aspect ratio of 4 Setting SettingAuto Setup LanguageSetting Logo CaptureCeiling RearStandby mode Power managementLamp mode On startRemote control PointerUSB Key lockPIN code lock To Change the PIN Code Lock settingTo Change the PIN Code Lamp counter reset Factory defaultFan Factory default FanMaintenance and Cleaning CleaningProjector is shut down and the Warning indicator lights red Then check the matters belowCleaning the Air Filters Attaching the Lens CoverCleaning the Projector Cabinet Cleaning the Projection LensMaintenance & Cleaning Lamp Replacement Reset the Lamp replace counterWhen the lamp replace counter is reset, the Lamp Lamp Replace CounterTroubleshooting AppendixRemote Control does not work AppendixComputer 2 cannot be selected Terminal item cannot be selectedMenu Tree System Setting Image SelectIndicators and Projector Condition Projector ConditionCompatible Computer Specifications XGA 1024 x 61.00 75.70Technical Specifications Accessories Optional PartsThis cable is used for RGB Scart 21-Pin Video output of video equipmentConfigurations of Terminals USB Connector Series BTerminal HDB15-PIN Terminal DVI-IPIN Code Lock No PIN Code Number MemoLogo PIN Code Lock No Key to better communications Canada