Eiki LC-SB21 owner manual Laser Pointer Function

Page 12

Part Names and Functions

Laser Pointer Function

This remote control emits a laser beam from the laser light window. With the LASER button pressed, laser light goes on. The signal emission indicator lights red and laser is emitted with red light. With the LASER button pressed for more than 1 minute or released, the light goes off.

The laser emitted is a class II laser. Do not look into the laser light window or shine the laser beam on yourself or other people. Below are the caution labels for laser beam.

CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not look into the laser light window while laser is emitted, otherwise eye damage may result.

These caution labels are put on the remote control.

Signal Emission Indicator

Laser Light Window

Pointer Function

You can move Spotlight or Pointer of the projector with the remote control to emphasize a part of the projected image.

1

With pressing the MENU button, hold down the NO SHOW

 

button for more than 7 seconds so that the Pointer function

 

will be available. (The Laser pointer has switched to the

 

Pointer.)

2

Press the LASER button on the remote control toward the

 

projector. Spotlight or Pointer is displayed on the screen with

 

the LASER button lighting green. Then move the Spotlight

 

or Pointer with the PRESENTATION POINTER button. If the

 

LASER button does not light green and still emits laser

 

beam, try the procedure above until the LASER button lights

 

green.

3

To clear the Spotlight or Pointer out the screen, press the

 

LASER button toward the projector and see if the LASER

button lighting turns off.

To switch back to the Laser pointer again, hold down the NO SHOW button with pressing the MENU button for more than 7 seconds or slide the RESET/ON/ALL-OFF switch to "RESET". (p11)

NO SHOW button

While pressing the MENU button, hold down the NO SHOW button for more than 7 seconds.

PRESENTATION POINTER button

MENU button

Spotlight

Pointer

Note:

You can choose the size of Spotlight (Large, Middle, and Small) and the pattern of Pointer (Arrow, Finger, and Dot) in the Setting Menu. See “Pointer” on page 46.

PRESENTATION POINTER button

LASER button

After the Laser pointer has switched to the Pointer, use the LASER button as the Pointer function ON-OFF switch. Press the LASER button toward the projector and see if it lights green.

12

Image 12
Contents Model LC-SB21 Features and Design Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandInstalling the Projector in Proper Position Air CirculationMoving the Projector Compliance Federal Communication Commission NoticePart Names and Functions FrontBack Bottom Rear Terminal Part Names and FunctionsTop Control Remote Control @1 !3Laser Pointer Function Pointer FunctionWireless Mouse Operation Operating RangePart Names FunctionsRemote Control Code Remote Control Battery InstallationButton. The code switches sequentially for one pressing With holding down the Menu button, press the ImageInstallation Adjustable FeetPositioning the Projector Connecting the AC Power Cord For the U.S.A. and Canada200 240 V AC Connecting to a Computer InstallationConnecting to Video Equipment CableConnecting to Component Video Equipment Monitor OUTWhat is PIN code? Basic OperationTurning On the Projector Enter a PIN codeTurning Off the Projector Basic OperationHow to Operate the On-Screen Menu Remote ControlOn-Screen Menu Top ControlMenu Bar Basic OperationZoom and Focus Adjustment Auto Setup FunctionKeystone Adjustment Picture Freeze FunctionNo Show Function BasicTimer Function Sound AdjustmentVolume MuteComputer Input Input Source SelectionComputer Input Computer System Selection AutoMode PC System MenuAuto PC Adjustment PC Adjust MenuTo store adjustment parameters Auto PC AdjManual PC Adjustment Reset Mode freeDisplay area Display area HImage Level Selection Image Level Adjustment Screen Size Adjustment Video Input Input Source Selection Video, S-VideoVideo Input Input button Video Computer Video buttonInput Source Selection Component, RGB Scart 21-Pin Input button Computer Video Computer buttonVideo System Selection AutoAV System Menu Video or S-Video AV System Menu ComponentCinema Image1~4Image button Dynamic Standard Cinema BlackboardGreen Color TintProgressive FilmProvides image at a normal video aspect ratio of 4 Setting SettingAuto Setup LanguageSetting Logo CaptureCeiling RearStandby mode Power managementLamp mode On startRemote control PointerUSB Key lockTo Change the PIN Code Lock setting PIN code lockTo Change the PIN Code Lamp counter reset Factory defaultFan Factory default FanMaintenance and Cleaning CleaningProjector is shut down and the Warning indicator lights red Then check the matters belowCleaning the Air Filters Attaching the Lens CoverCleaning the Projection Lens Cleaning the Projector CabinetMaintenance & Cleaning Lamp Replacement Reset the Lamp replace counterWhen the lamp replace counter is reset, the Lamp Lamp Replace CounterTroubleshooting AppendixRemote Control does not work AppendixComputer 2 cannot be selected Terminal item cannot be selectedMenu Tree System Setting Image SelectIndicators and Projector Condition Projector ConditionCompatible Computer Specifications XGA 1024 x 61.00 75.70Technical Specifications Accessories Optional PartsThis cable is used for RGB Scart 21-Pin Video output of video equipmentConfigurations of Terminals USB Connector Series BTerminal HDB15-PIN Terminal DVI-IPIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Key to better communications Canada