Eiki LC-SB21 owner manual Indicators and Projector Condition

Page 58

Appendix

Indicators and Projector Condition

Check the indicators for projector condition.

Indicators
	WARNING	LAMP	Projector Condition
POWER	WARNING	REPLACE
red/green	red	yellow
			The projector is OFF. (The AC power cord is unplugged.)
		✽	The projector is preparing for stand-by or the projection lamp is being
		✽	cooled down. The projector cannot be turned on until cooling is completed.

		✽	The projector is ready to be turned on with the POWER ON-OFF button.
		✽	The projector is operating normally.
		✽	The projector is in the Power management mode.
			The temperature inside the projector is abnormally high. The projector
			cannot be turned on. When the projector is cooled down enough and the
		✽	temperature returns to normal, the POWER indicator lights red and the
			projector can be turned on. (The WARNING . indicator keeps blinking.)
			Check and clean the Air filter.
			The projector has been cooled down enough and the temperature returns
		✽	to normal. When turning on the projector, the WARNING indicator stops
			blinking. Check and clean the air filters.
			The projector detects an abnormal condition and cannot be turned on.
			Unplug the AC power cord and plug it again to turn on the projector. If the
		✽	projector is turned off again, disconnect the AC power cord and contact the
			dealer or the service center for service and checkup. Do not leave the
			projector on. It may cause electric shock or a fire hazard.

• • • lights green.

• • • blinks green.

• • • lights red.

• • • blinks red.

• • • off

✽When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly. Reset the Lamp replace counter after replacement of the lamp. See page 52 and 53.

58

Image 58

Contents Model LC-SB21 Features and Design Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandAir Circulation Installing the Projector in Proper PositionMoving the Projector Compliance Federal Communication Commission NoticeFront Part Names and FunctionsBack Bottom Rear Terminal Part Names and FunctionsTop Control Remote Control @1 !3Laser Pointer Function Pointer FunctionPart Names Wireless Mouse OperationOperating Range FunctionsButton. The code switches sequentially for one pressing Remote Control CodeRemote Control Battery Installation With holding down the Menu button, press the ImageAdjustable Feet InstallationPositioning the Projector For the U.S.A. and Canada Connecting the AC Power Cord200 240 V AC Connecting to a Computer InstallationConnecting to Video Equipment CableConnecting to Component Video Equipment Monitor OUTTurning On the Projector What is PIN code?Basic Operation Enter a PIN codeTurning Off the Projector Basic OperationOn-Screen Menu How to Operate the On-Screen MenuRemote Control Top ControlMenu Bar Basic OperationZoom and Focus Adjustment Auto Setup FunctionNo Show Function Keystone AdjustmentPicture Freeze Function BasicVolume Timer FunctionSound Adjustment MuteInput Source Selection Computer InputComputer Input Mode Computer System SelectionAuto PC System MenuTo store adjustment parameters Auto PC AdjustmentPC Adjust Menu Auto PC AdjManual PC Adjustment Display area ResetMode free Display area HImage Level Selection Image Level Adjustment Screen Size Adjustment Video Input Video InputInput Source Selection Video, S-Video Input button Video Computer Video buttonInput Source Selection Component, RGB Scart 21-Pin Input button Computer Video Computer buttonAV System Menu Video or S-Video Video System SelectionAuto AV System Menu ComponentImage1~4 CinemaImage button Dynamic Standard Cinema BlackboardGreen Color TintProgressive FilmProvides image at a normal video aspect ratio of 4 Auto Setup SettingSetting LanguageSetting Ceiling LogoCapture RearLamp mode Standby modePower management On startUSB Remote controlPointer Key lockPIN code lock To Change the PIN Code Lock settingTo Change the PIN Code Fan Factory default Lamp counter resetFactory default FanProjector is shut down and the Warning indicator lights red Maintenance and CleaningCleaning Then check the matters belowCleaning the Air Filters Attaching the Lens CoverCleaning the Projector Cabinet Cleaning the Projection LensMaintenance & Cleaning Lamp Replacement Reset the Lamp replace counterWhen the lamp replace counter is reset, the Lamp Lamp Replace CounterTroubleshooting AppendixComputer 2 cannot be selected Remote Control does not workAppendix Terminal item cannot be selectedMenu Tree System Setting Image SelectIndicators and Projector Condition Projector ConditionCompatible Computer Specifications XGA 1024 x 61.00 75.70Technical Specifications This cable is used for RGB Scart 21-Pin AccessoriesOptional Parts Video output of video equipmentTerminal HDB15-PIN Configurations of TerminalsUSB Connector Series B Terminal DVI-IPIN Code Lock No PIN Code Number MemoLogo PIN Code Lock No Key to better communications Canada