Eiki LC-SB21 owner manual Maintenance and Cleaning, Then check the matters below

Page 49

Maintenance and Cleaning

Warning Indicator

The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance.

Maintenance

The projector is shut down and the WARNING indicator is blinking red.

When the temperature inside the projector exceeds the normal temperature, the projector is automatically shut down to protect the inside of the projector. The POWER indicator is blinking and the projector is being cooled down. When the temperature inside the projector returns to normal, the POWER indicator lights red and the projector can be turned on.

Note:

After the temperature inside the projector returns to normal, the WARNING indicator still continues to blink. When the projector is turned on again, the WARNING indicator stops blinking.

TOP CONTROL

WARNING

 

V

LAMP

 

O

 

L

REPLACE

LECT

U

M

 

 

 

 

E

 

 

+

 

WARNING blinking red

& Cleaning

Then check the matters below:

Did you provide appropriate space for the projector to be ventilated? Check the installing condition to see if ventilation slots are not blocked.

Is the projector not installed near the ventilation duct of air- conditioning equipment which may be hot? Install the projector away from the ventilation duct of air-conditioning equipment.

Are the air filters clean? Clean the air filters periodically. (p50)

The projector is shut down and the WARNING indicator lights red.

When the projector detects an abnormal condition, it is automatically shut down to protect the inside and the WARNING indicator lights red. In this case, disconnect the AC power cord and reconnect it, and then turn the projector on once again for check. If the projector is still turned off and the WARNING indicator lights red, disconnect the AC power cord and contact the service station for check and repair.

CAUTION

DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER THE ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK.

TOP CONTROL

WARNING

 

V

LAMP

 

O

LECT

L

REPLACE

U

 

 

M

 

 

E

 

 

+

 

WARNING lights red

49

Image 49
Contents Model LC-SB21 Features and Design Table of Contents Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsAir Circulation Installing the Projector in Proper PositionMoving the Projector Federal Communication Commission Notice ComplianceFront Part Names and FunctionsBack Bottom Part Names and Functions Rear TerminalTop Control @1 !3 Remote ControlPointer Function Laser Pointer FunctionOperating Range Wireless Mouse OperationPart Names FunctionsRemote Control Battery Installation Remote Control CodeButton. The code switches sequentially for one pressing With holding down the Menu button, press the ImageAdjustable Feet InstallationPositioning the Projector For the U.S.A. and Canada Connecting the AC Power Cord200 240 V AC Installation Connecting to a ComputerCable Connecting to Video EquipmentMonitor OUT Connecting to Component Video EquipmentBasic Operation What is PIN code?Turning On the Projector Enter a PIN codeBasic Operation Turning Off the ProjectorRemote Control How to Operate the On-Screen MenuOn-Screen Menu Top ControlBasic Operation Menu BarAuto Setup Function Zoom and Focus AdjustmentPicture Freeze Function Keystone AdjustmentNo Show Function BasicSound Adjustment Timer FunctionVolume MuteInput Source Selection Computer InputComputer Input Auto Computer System SelectionMode PC System MenuPC Adjust Menu Auto PC AdjustmentTo store adjustment parameters Auto PC AdjManual PC Adjustment Mode free ResetDisplay area Display area HImage Level Selection Image Level Adjustment Screen Size Adjustment Input Source Selection Video, S-Video Video InputVideo Input Input button Video Computer Video buttonInput button Computer Video Computer button Input Source Selection Component, RGB Scart 21-PinAuto Video System SelectionAV System Menu Video or S-Video AV System Menu ComponentImage1~4 CinemaImage button Dynamic Standard Cinema BlackboardGreen Tint ColorFilm ProgressiveProvides image at a normal video aspect ratio of 4 Setting SettingAuto Setup LanguageSetting Capture LogoCeiling RearPower management Standby modeLamp mode On startPointer Remote controlUSB Key lockPIN code lock To Change the PIN Code Lock settingTo Change the PIN Code Factory default Lamp counter resetFan Factory default FanCleaning Maintenance and CleaningProjector is shut down and the Warning indicator lights red Then check the matters belowAttaching the Lens Cover Cleaning the Air FiltersCleaning the Projector Cabinet Cleaning the Projection LensMaintenance & Cleaning Reset the Lamp replace counter Lamp ReplacementLamp Replace Counter When the lamp replace counter is reset, the LampAppendix TroubleshootingAppendix Remote Control does not workComputer 2 cannot be selected Terminal item cannot be selectedMenu Tree Image Select System SettingProjector Condition Indicators and Projector ConditionXGA 1024 x 61.00 75.70 Compatible Computer SpecificationsTechnical Specifications Optional Parts AccessoriesThis cable is used for RGB Scart 21-Pin Video output of video equipmentUSB Connector Series B Configurations of TerminalsTerminal HDB15-PIN Terminal DVI-IPIN Code Lock No PIN Code Number MemoLogo PIN Code Lock No Key to better communications Canada