Eiki LC-SB21 owner manual Cleaning the Air Filters, Attaching the Lens Cover

Page 50

Maintenance and Cleaning

Cleaning the Air Filters

Air filters prevent dust from accumulating on the surface of the optical elements inside the projector. Should the air filters become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat build up and adversely affect the life of the projector. Clean the air filters following the steps below.

1

Turn off the projector, and disconnect the AC power cord

 

from the AC outlet.

2

Turn the projector upside down and remove the air filters by

 

pulling the latches upward.

3

Clean the air filters with a brush or rinse them softly.

 

Clean the ventillation slots around the air filter too.

4

When cleaning the air filters by rinsing, dry them well.

 

Replace the air filters properly. Make sure that the air filters

are fully inserted.

CAUTION

Do not operate the projector with the air filters removed. Dust may accumulate on the LCD panel and the projection mirror degrading picture quality.

Do not put small parts into the air intake vents. It may result in malfunction of the projector.

Air Filter

Pull up and remove.

RECOMMENDATION

We recommend avoiding dusty/smoky environments when operating the projector. Usage in these environments may cause poor image quality.

When using the projector under dusty or smoky conditions, dust may accumulate on a lens, LCD panels, or optical elements inside the projector. This condition may degrade the quality of a projected image.

When the symptoms above are noticed, contact your authorized dealer or service station for proper cleaning.

Attaching the Lens Cover

When moving this projector or while not using it over an extended period of time, replace the lens cover.

1

Pass the string through a hole of the lens cover.

2

Turn the projector upside down.

3

Attach the string with lens cover to a hole on the bottom of

 

the projector and secure it with a screw.

Lens Cover

String for the lens cover

Secure it to the hole with a screw.

Hole

50

Image 50
Contents Model LC-SB21 Features and Design Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandMoving the Projector Installing the Projector in Proper PositionAir Circulation Compliance Federal Communication Commission NoticeBack Bottom Part Names and FunctionsFront Rear Terminal Part Names and FunctionsTop Control Remote Control @1 !3Laser Pointer Function Pointer FunctionPart Names Wireless Mouse OperationOperating Range FunctionsButton. The code switches sequentially for one pressing Remote Control CodeRemote Control Battery Installation With holding down the Menu button, press the ImagePositioning the Projector InstallationAdjustable Feet 200 240 V AC Connecting the AC Power CordFor the U.S.A. and Canada Connecting to a Computer InstallationConnecting to Video Equipment CableConnecting to Component Video Equipment Monitor OUTTurning On the Projector What is PIN code?Basic Operation Enter a PIN codeTurning Off the Projector Basic OperationOn-Screen Menu How to Operate the On-Screen MenuRemote Control Top ControlMenu Bar Basic OperationZoom and Focus Adjustment Auto Setup FunctionNo Show Function Keystone AdjustmentPicture Freeze Function BasicVolume Timer FunctionSound Adjustment MuteComputer Input Computer InputInput Source Selection Mode Computer System SelectionAuto PC System MenuTo store adjustment parameters Auto PC AdjustmentPC Adjust Menu Auto PC AdjManual PC Adjustment Display area ResetMode free Display area HImage Level Selection Image Level Adjustment Screen Size Adjustment Video Input Video InputInput Source Selection Video, S-Video Input button Video Computer Video buttonInput Source Selection Component, RGB Scart 21-Pin Input button Computer Video Computer buttonAV System Menu Video or S-Video Video System SelectionAuto AV System Menu ComponentImage button Dynamic Standard Cinema BlackboardGreen CinemaImage1~4 Color TintProgressive FilmProvides image at a normal video aspect ratio of 4 Auto Setup SettingSetting LanguageSetting Ceiling LogoCapture RearLamp mode Standby modePower management On startUSB Remote controlPointer Key lockTo Change the PIN Code To Change the PIN Code Lock settingPIN code lock Fan Factory default Lamp counter resetFactory default FanProjector is shut down and the Warning indicator lights red Maintenance and CleaningCleaning Then check the matters belowCleaning the Air Filters Attaching the Lens CoverMaintenance & Cleaning Cleaning the Projection LensCleaning the Projector Cabinet Lamp Replacement Reset the Lamp replace counterWhen the lamp replace counter is reset, the Lamp Lamp Replace CounterTroubleshooting AppendixComputer 2 cannot be selected Remote Control does not workAppendix Terminal item cannot be selectedMenu Tree System Setting Image SelectIndicators and Projector Condition Projector ConditionCompatible Computer Specifications XGA 1024 x 61.00 75.70Technical Specifications This cable is used for RGB Scart 21-Pin AccessoriesOptional Parts Video output of video equipmentTerminal HDB15-PIN Configurations of TerminalsUSB Connector Series B Terminal DVI-ILogo PIN Code Lock No PIN Code Number MemoPIN Code Lock No Key to better communications Canada