Eiki LC-XGC500 Picture is not bright enough, Color is strange, Image is Left/Right reversed

Page 70

Appendix

Picture is not bright enough.

Projecting from the excessive slant angle to the screen may cause keystone distortion and partial imperfect focus.

Check if "Contrast" or "Brightness" are adjusted properly See page 42.

Check if "Image level" is selected properly See page 41.

Check the LAMP 1/2 REPLACE indicators. If it lights, the end of lamp life is approaching. Replace the lamp with a new one promptly. See pages 63-65, 74.

Check the Lamp control function See page 52.

The color is strange..

– Check the Input signal, color system, video system, or computer

 

system mode.

 

– Adjust the Image level properly. See page 41.

Image is Left/Right reversed..

– Check the Ceiling/Rear function. See page 45.

Image is Top/Bottom reversed..

– Check the Ceiling function. See page 45.

The image is distorted or runs off..

– Check the "PC Adjustment" menu or "Screen" menu and adjust them.

 

See pages 37-40, 45-48.

The edge of image is distorted..

– With maximum lens shift, image distortion may be observed.

No sound

– Check the audio cable connection from audio input source.

 

– Adjust the audio source.

 

– Press the Volume + button. See page 29.

 

– Press the Mute button. See page 29.

 

– When the AUDIO OUT is plugged in, the projector's built-in speaker is

 

not available. See page 22.

 

– Is the image projected? You will hear the sound only when the image is

 

projected.

Auto PC adjustment function

– Check the Input signal. Auto PC Adjustment function can not work,

does not work..

when 480p, 575p, 720p, 480i, 575i, 1035i, or 1080i is selected.

 

See page 38.

 

– The Auto adj. icon turns gray and cannot be operated with the digital

 

signals. See page 38.

Some displays are not seen

– Check the Display function. See page 54.

during the operation..

 

The setting does not remain after

– Make sure you selected "Store" after adjusting settings. Some settings

turning off power..

cannot be stored if not registered with "Store."

Power management function does

– Power management function cannot work while "Freeze" function is

not work..

running or the shutter is closed.

Image disappears automatically

– Check the power management function in the Setting. The power

 

management is set to “On” at the factory.

69

Image 70
Contents Model LC-XGC500 LC-XGC500L Español EnglishFrançais DeutschFeatures and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Air Circulation Top ControlInstalling the Projector in Proper Directions Positioning PrecautionsMoving the Projector Transporting the ProjectorAC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Front Part Names and FunctionsBack Audio 3 Jacks LMONO/R Side TerminalAudio 2 Jack BNC Input Jacks0USB Connector Series B 1R/C JackTop Control Remote Control 5D..ZOOM button 4P-TIMER button9RESET/ON/ALL-OFF switch 6ZOOM ed buttonsRemote Control Battery Installation Wired Remote ControlRemote Control Code Adjustable FeetPositioning the Projector for LC-XGC500 InstallationMoving the Lens Removing the lens Lens InstallationAttaching the lens to the projector Connecting to a Computer Digital and Analog RGB Cables used for connection VGAConnecting for Audio Signal Monitor OUT and Audio OUT SpecificationsConnecting the AC Power Cord Projector side AC outlet sideTurning On the Projector What is PIN code?Basic Operation Enter a PIN codeTurning Off the Projector Remote Control How to Operate the On-Screen MenuOn-Screen Menu Menu Bar Lens Shift Adjustment Zoom AdjustmentFocus Adjustment Operating with Projector ControlDirect Operation Sound AdjustmentMenu Operation Operating with Remote Control Shutter button Timer buttonKeystone button Pointer Function Laser Pointer FunctionSpotlight Wireless Mouse Operation Presentation Pointer buttonInput Selection Remote Control OperationRemote Control button operation InputRGB PC analog RGB Scart RGB PC digital Input Source SelectionInput Menu Video ComponentComponent Video System SelectionVideo or S-video AV System Menu Video or S-videoSelecting Computer System Manually Computer AdjustmentComputer System Selection PC System MenuTo store adjustment parameters Auto PC AdjustmentPC Adjust Menu Auto PC AdjManual PC Adjustment To clear the adjusted data To store the adjusted dataImage Level Selection Image Level SelectionImage Menu Image Adjustment Image AdjustmentImage Adjust Menu Noise reduction SharpnessGamma ProgressiveTo reset the adjusted data, select Reset and press Screen Menu Screen AdjustmentScreen Adjustment KeystoneScreen Size Adjustment Computer Signals Digital zoom + For zooming in and out the imagesDigital zoom Screen Size Adjustment Video, Component Signals Setting Menu Language SettingSetting LogoCapture Logo PIN code lockEnter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code Lamp control Lamp modeLamp life control Pointer Display Standby modePower management DisplayOn start Slant settingSlant Key lock Security Key lock and PIN code lock settingsKey lock PIN code lock Change the PIN code lock settingChange the PIN code lock setting Enter a PIN codeChange the PIN code Change the PIN codeTest pattern Factory default Factory defaultMaintenance and Care Filter InstructionsReplacing the Filter Cartridge Replacement Filter Cartridge Service Parts Code 610 342Model No.. of your projector LC-XGC500, LC-XGC500L Filter counter Scroll counterAuto Lamp Selection System Lamp 1/2 Replace IndicatorsLamp Mode Changeover Lamp Status DisplayLamp Replacement Order Replacement Lamp POA-LMP125 Service Parts No 342Then check the matters below Cleaning the Projection Lens Cleaning the Projector CabinetNo power TroubleshootingProblem AppendixTurning off power Auto PC adjustment functionDuring the operation Setting does not remain after Power management function doesWireless Mouse function does Remote Control doesWired remote control does not Indicator blinks or lightsSystem Menu TreeInput InformationPC Adjust Screen SettingIndicators and Projector Condition Projector is operating normallyProjector is detecting abnormal condition ImmediatelyIf the Filter counter reached a time set in the timer Compatible Computer Specifications ON-SCREEN Resolution59.940 Technical Specifications Optional Parts PJ Link Notice Output Configurations of TerminalsTerminal Analog RGB Mini D-sub 15 pin Input Terminal D-sub 9 pinPIN Code Number Memo Logo PIN Code Lock NoDimensions Deutschland & Österreich