Eiki LC-XE10 instruction manual Installation, Positioning the Projector, Adjustable Feet

Page 16

Installation

Positioning the Projector

This projector is designed to project on a flat projection surface and can be focused from 4.3’(1.3m) - 33.1’(10.1m). Refer to the figure and the table below for the screen size and the distance between the projector and the screen.

A : B = 9 : 1

 

33.1' (10.1m)

 

 

 

 

 

 

300”

(Inch Diagonal)

25.3' (7.7m)

 

 

 

 

16.4' (5.0m)

 

231”

Max. Zoom

 

 

 

 

10.8' (3.3m)

150”

 

231”

 

4.3' (1.3m)

 

Min. Zoom

A

 

178”

 

 

 

100”

 

 

 

 

 

 

 

40”

115”

 

 

 

 

 

 

 

77”

 

 

 

 

31”

 

 

 

(Center)

 

 

 

 

 

 

 

 

B

Screen Size

 

40”

 

100”

150”

231”

300”

(W x H) mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

813 x 610

 

2032 x 1524

3048 x 2286

4694 x 3520

6096 x 4572

4 : 3 aspect ratio

 

 

 

 

 

 

 

 

 

 

Zoom (min)

 

5.6' (1.7m)

 

14.4' (4.4m)

21.7' (6.6m)

33.1' (10.1m)

––-––

 

 

 

 

 

 

 

 

Zoom (max)

 

4.3' (1.3m)

 

10.8' (3.3m)

16.4' (5.0m)

25.3' (7.7m)

33.1' (10.1m)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTE

The brightness in a room has a great influence on picture quality. It is recommended to limit ambient lighting in order to provide the best image.

The values shown are approximate and may vary from the actual size.

Adjustable Feet

Projection angle can be adjusted up to 10.3 degrees with the adjustable feet.

1Lift the front of the projector and pull the feet lock latches on both sides of the projector.

2Release the feet lock latches to lock the adjustable feet and rotate the adjustable feet to adjust the position and tilt.

3To retract the adjustable feet, lift the front of the projector and pull and undo the feet lock latches.

Keystone distortion of the projected image can be adjusted by menu operation. (p20, 21, 39)

CAUTION

Tilt the projector within the adjustable range in order not to shorten the life of the lamp. Proper angle should be taken. See page 5.

Feet Lock Latches

Adjustable Feet

16

Image 16
Contents Model LC-XE10 Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandSafety Instructions Installing the Projector in Proper PositionAir Circulation Moving the ProjectorCompliance Federal Communication Commission NoticeCompliance For Continental EuropeFor the U.S.A. and Canada 200 240 V ACFeatures and Design Part Names and Functions Front Back BottomPart Names and Functions TerminalTop Auto PC ADJ. button Point Up/Down/Left/Right buttonRemote Control Signal Emission indicator Laser Pointer Function Pointer FunctionRemote Control Code Wireless Mouse OperationRemote Control Operating Range Remote Control Batteries InstallationAdjustable Feet InstallationPositioning the Projector Connecting to a Computer InstallationTerminals Projector Video Source example Connecting to Video EquipmentVideo Cable RCA x Scart-VGA Cable Turning On the Projector Basic OperationTurning Off the Projector Zoom Adjustment Focus AdjustmentKeystone Adjustment Basic OperationPicture Freeze Function Auto Set Up FunctionKeystone correction Corner Timer Function Sound AdjustmentNo Show Function Direct OperationRemote Control On-Screen MenuTop Control On-Screen MenuMenu Bar Computer Input Input Source SelectionComputer Input Computer System SelectionAuto ModeComputer Adjustment Auto PC Adjust MenuTo store adjustment data Auto PC AdjComputer Adjustment Manual Reset Mode freeDisplay area To store adjustment data To clear adjustment dataImage Level Selection Image Level Adjustment Screen Size Adjustment Video Input Input Source Selection Video, S-Video, Y, Pb/Cb, Pr/CrPb/Cb, Pr/Cr Input button Video Computer Video button VideoVideo Input Input Source Selection RGB Scart 21-PinRGB Scart Input button Computer Video Computer 2 buttonVideo or S-Video Video System SelectionComponent Cinema Image button Standard CinemaTint ColorProgressive Resets all adjustment to their previous figure Setting SettingSetting Power management Lamp modeOn start PointerTo change the code for the remote control Wireless Mouse modeProjector mode To change the code for the projectorProjector is shut down and the Warning indicator lights red Maintenance and CleaningThen check the items below Maintenance and Cleaning Cleaning the Air FiltersCleaning the Projection Lens Cleaning the Projector CabinetLamp Replacement Reset the Lamp replace counterLamp Handling Precautions Lamp Replace CounterTroubleshooting AppendixAppendix Indicators and Projector Condition Projector is OFF. The AC power cord is unpluggedPC Adjust Image Adjust ScreenMenu Tree InputImage Select SettingSound Freq Compatible Computer SpecificationsKHz Technical Specifications Terminal HDB15-PIN Pin Configuration Configurations of TerminalsTerminal DVI-I Pin Configuration Optional Parts Attaching the Lens Cover Key registration Deleting key registrationTo lock the projector with USB key Off Projector is not locked with USB Key On1Appendix Appendix Key to better communications Canada
Related manuals
Manual 60 pages 26.38 Kb