Eiki LC-XE10 instruction manual Setting

Page 40

Setting

Logo

This function decides what to be displayed when starting up.

User

···· the image you captured

Default

···· the factory-set logo

Off

···· count-down only

Capture

This function is used to capture the image being projected and use it for a starting-up display or interval of presentations. After capturing the projected image, go to the Logo function and set it as “User”. Then the captured image will be displayed when turning on the projector next time or pressing the NO SHOW button. (p22)

To capture the image, select [Yes]. To cancel the Capture function, select [No].

Before capturing an image, select Standard in the Image Select Menu to capture a proper image. (See page 30, 36.)

A signal from a computer can be captured up to XGA(1024 x 768). A signal from video equipment can be captured except for 720p, 1035i, and 1080i. When capturing the image that has been adjusted by the Keystone function, the adjustment data is automatically reset and the projector captures an image without keystone adjustment.

Capture

Select [Yes] to capture the projected image.

Press the SELECT button at this icon to display other items.

Select [Yes] to stop capturing.

Ceiling

When this function is “On,” the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling mounting the projector.

Rear

When this function is “On,” the picture is left/right reversed. This function is used to project the image to a rear projection screen.

Terminal

The COMPUTER IN 2/MONITOR OUT terminal on the back of the projector can be used as computer input or monitor output by switching Terminal with the Point Left/Right button.

To use the terminal as computer input or RGB Scart 21-Pin Video input, select Computer 2. To use the terminal as monitor out, select Monitor out.

Terminal cannot be switched into Monitor out after selecting Computer 2. In this case, select other input source such as Computer 1 or Video, and you will select Terminal.

Standby mode

This function is available when using Multi Card Director optionally supplied, and it reduces standby energy when selecting Eco.

Eco

···· reduces standby energy.

Normal ···· consumes normal standby energy.

Ceiling

Rear

Standby mode

Press the SELECT button at this icon to display previous items.

Move the pointer to item and then press POINT LEFT/RIGHT button(s).

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Model LC-XE10 Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandSafety Instructions Installing the Projector in Proper PositionAir Circulation Moving the ProjectorCompliance Federal Communication Commission NoticeCompliance For Continental EuropeFor the U.S.A. and Canada 200 240 V ACFeatures and Design Part Names and Functions Front Back BottomPart Names and Functions TerminalTop Auto PC ADJ. button Point Up/Down/Left/Right buttonRemote Control Signal Emission indicatorLaser Pointer Function Pointer FunctionRemote Control Code Wireless Mouse OperationRemote Control Operating Range Remote Control Batteries InstallationAdjustable Feet InstallationPositioning the Projector Connecting to a Computer InstallationTerminals Projector Video Source example Connecting to Video EquipmentVideo Cable RCA x Scart-VGA Cable Turning On the Projector Basic OperationTurning Off the Projector Zoom Adjustment Focus AdjustmentKeystone Adjustment Basic OperationPicture Freeze Function Auto Set Up FunctionKeystone correction Corner Timer Function Sound AdjustmentNo Show Function Direct OperationRemote Control On-Screen MenuTop Control On-Screen MenuMenu Bar Computer Input Input Source SelectionComputer Input Computer System SelectionAuto ModeComputer Adjustment Auto PC Adjust MenuTo store adjustment data Auto PC AdjComputer Adjustment Manual Reset Mode freeDisplay area To store adjustment data To clear adjustment dataImage Level Selection Image Level Adjustment Screen Size Adjustment Video Input Input Source Selection Video, S-Video, Y, Pb/Cb, Pr/CrPb/Cb, Pr/Cr Input button Video Computer Video button VideoVideo Input Input Source Selection RGB Scart 21-PinRGB Scart Input button Computer Video Computer 2 buttonVideo or S-Video Video System SelectionComponent Cinema Image button Standard CinemaTint ColorProgressive Resets all adjustment to their previous figure Setting SettingSetting Power management Lamp modeOn start PointerTo change the code for the remote control Wireless Mouse modeProjector mode To change the code for the projectorProjector is shut down and the Warning indicator lights red Maintenance and CleaningThen check the items below Maintenance and Cleaning Cleaning the Air FiltersCleaning the Projection Lens Cleaning the Projector CabinetLamp Replacement Reset the Lamp replace counterLamp Handling Precautions Lamp Replace CounterTroubleshooting AppendixAppendix Indicators and Projector Condition Projector is OFF. The AC power cord is unpluggedPC Adjust Image Adjust ScreenMenu Tree InputImage Select SettingSound Freq Compatible Computer SpecificationsKHz Technical Specifications Terminal HDB15-PIN Pin Configuration Configurations of TerminalsTerminal DVI-I Pin Configuration Optional Parts Attaching the Lens Cover Key registration Deleting key registrationTo lock the projector with USB key Off Projector is not locked with USB Key On1Appendix Appendix Key to better communications Canada
Related manuals
Manual 60 pages 26.38 Kb

LC-XE10 specifications

The Eiki LC-XE10 is a high-performance LCD projector designed for a wide range of applications, including business presentations, educational environments, and home entertainment. With its combination of advanced features, robust technology, and user-friendly design, the LC-XE10 stands out as an ideal choice for professionals and enthusiasts alike.

One of the main features of the Eiki LC-XE10 is its impressive brightness level, which reaches up to 5000 lumens. This high brightness allows it to produce sharp and vivid images even in well-lit environments, making it perfect for conference rooms and classrooms. The projector's native XGA (1024 x 768) resolution ensures clarity in both text and graphics, which is particularly beneficial for presentations that require detailed information.

The LC-XE10 utilizes advanced 3LCD technology, providing excellent color accuracy and vibrant images. This technology minimizes the risk of color imbalances and delivers true-to-life colors, ensuring that presentations are visually appealing and engaging. Additionally, the projector supports a range of input options, including HDMI, VGA, and composite video, making it compatible with various devices, such as laptops, DVD players, and document cameras.

Another key characteristic of the Eiki LC-XE10 is its longevity. With a lamp life of up to 4000 hours in normal mode, users can enjoy extended usage without the need for frequent replacements. The projector is designed with ease of maintenance in mind, featuring a simple lamp replacement process and a dust filter that helps prolong the device's lifespan.

For those who value versatility, the LC-XE10 includes a powered zoom and focus lens, offering a focal length of 1.2 to 1.44, making it suitable for various screen sizes and room configurations. The projector also features a horizontal and vertical keystone correction function, which helps to achieve a perfectly rectangular image even when the projector is not centrally aligned with the screen.

In conclusion, the Eiki LC-XE10 is an outstanding LCD projector that combines high brightness, excellent color performance, and user-friendly features. Its reliable performance and flexible connectivity options make it a perfect choice for anyone looking to deliver impactful presentations or enjoy high-quality visual content.
Top Page Image Contents