Eiki LC-XE10 instruction manual Lamp Replacement, Reset the Lamp replace counter

Page 45

Maintenance and Cleaning

Lamp Replacement

When the life of the projection lamp of this projector draws to an end,

the LAMP REPLACE indicator lights yellow. If this indicator lightsTop Control yellow, replace the lamp with a new one promptly.

This indicator lights yellow when the life of the projection lamp draws to an end.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION

 

 

 

CAUTION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Allow a projector to cool, for at least 45 minutes before

For continued safety, replace with a lamp of the same

 

you open the Lamp cover. The inside of the projector

 

type. Do not drop a lamp or touch a glass bulb! The

 

 

can become very hot.

 

glass can shatter and may cause injury.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Follow these steps to replace the lamp.

1Turn off the projector and disconnect the AC plug. Allow the projector to cool for at least 45 minutes.

2Insert the coin etc. and pushing it, then remove the lamp cover upward.

3Loosen 2 screws of the lamp with a screwdriver and pull out the lamp by grasping the handle.

4Replace the lamp with a new one and tighten the 2 screws back into position. Make sure that the lamp is set properly. Replace the lamp cover.

5Connectprojector.the AC power cord to the projector and turn on the

6Reset the Lamp replace counter.

See “Lamp Replace Counter” on the next page .

Lamp Cover

Screw

Lamp

Handle

ORDER REPLACEMENT LAMP

Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer.

●

Model No. of your projector

:

LC-XE10

●

Replacement Lamp Type No.

:

POA-LMP68

 

 

 

(Service Parts No. 610 308 1786)

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Model LC-XE10 Table of Contents Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsInstalling the Projector in Proper Position Safety InstructionsAir Circulation Moving the ProjectorFederal Communication Commission Notice ComplianceFor Continental Europe ComplianceFor the U.S.A. and Canada 200 240 V ACFeatures and Design Front Back Bottom Part Names and FunctionsTerminal Part Names and FunctionsAuto PC ADJ. button Point Up/Down/Left/Right button TopSignal Emission indicator Remote ControlPointer Function Laser Pointer FunctionWireless Mouse Operation Remote Control CodeRemote Control Batteries Installation Remote Control Operating RangeInstallation Adjustable FeetPositioning the Projector Installation Connecting to a ComputerTerminals Projector Connecting to Video Equipment Video Source exampleVideo Cable RCA x Scart-VGA Cable Basic Operation Turning On the ProjectorTurning Off the Projector Focus Adjustment Zoom AdjustmentKeystone Adjustment Basic OperationAuto Set Up Function Picture Freeze FunctionKeystone correction Corner Sound Adjustment Timer FunctionNo Show Function Direct OperationOn-Screen Menu Remote ControlTop Control On-Screen MenuMenu Bar Input Source Selection Computer InputComputer System Selection Computer InputAuto ModePC Adjust Menu Computer Adjustment AutoTo store adjustment data Auto PC AdjComputer Adjustment Manual Mode free ResetDisplay area To store adjustment data To clear adjustment dataImage Level Selection Image Level Adjustment Screen Size Adjustment Input Source Selection Video, S-Video, Y, Pb/Cb, Pr/Cr Video InputPb/Cb, Pr/Cr Input button Video Computer Video button VideoInput Source Selection RGB Scart 21-Pin Video InputRGB Scart Input button Computer Video Computer 2 buttonVideo System Selection Video or S-VideoComponent Image button Standard Cinema CinemaColor TintProgressive Resets all adjustment to their previous figure Setting SettingSetting Lamp mode Power managementOn start PointerWireless Mouse mode To change the code for the remote controlProjector mode To change the code for the projectorMaintenance and Cleaning Projector is shut down and the Warning indicator lights redThen check the items below Cleaning the Air Filters Maintenance and CleaningCleaning the Projection Lens Cleaning the Projector CabinetReset the Lamp replace counter Lamp ReplacementLamp Replace Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Projector is OFF. The AC power cord is unplugged Indicators and Projector ConditionImage Adjust Screen PC AdjustMenu Tree InputSetting Image SelectSound Compatible Computer Specifications FreqKHz Technical Specifications Configurations of Terminals Terminal HDB15-PIN Pin ConfigurationTerminal DVI-I Pin Configuration Optional Parts Attaching the Lens Cover Deleting key registration Key registrationTo lock the projector with USB key Off Projector is not locked with USB Key On1Appendix Appendix Key to better communications Canada
Related manuals
Manual 60 pages 26.38 Kb

LC-XE10 specifications

The Eiki LC-XE10 is a high-performance LCD projector designed for a wide range of applications, including business presentations, educational environments, and home entertainment. With its combination of advanced features, robust technology, and user-friendly design, the LC-XE10 stands out as an ideal choice for professionals and enthusiasts alike.

One of the main features of the Eiki LC-XE10 is its impressive brightness level, which reaches up to 5000 lumens. This high brightness allows it to produce sharp and vivid images even in well-lit environments, making it perfect for conference rooms and classrooms. The projector's native XGA (1024 x 768) resolution ensures clarity in both text and graphics, which is particularly beneficial for presentations that require detailed information.

The LC-XE10 utilizes advanced 3LCD technology, providing excellent color accuracy and vibrant images. This technology minimizes the risk of color imbalances and delivers true-to-life colors, ensuring that presentations are visually appealing and engaging. Additionally, the projector supports a range of input options, including HDMI, VGA, and composite video, making it compatible with various devices, such as laptops, DVD players, and document cameras.

Another key characteristic of the Eiki LC-XE10 is its longevity. With a lamp life of up to 4000 hours in normal mode, users can enjoy extended usage without the need for frequent replacements. The projector is designed with ease of maintenance in mind, featuring a simple lamp replacement process and a dust filter that helps prolong the device's lifespan.

For those who value versatility, the LC-XE10 includes a powered zoom and focus lens, offering a focal length of 1.2 to 1.44, making it suitable for various screen sizes and room configurations. The projector also features a horizontal and vertical keystone correction function, which helps to achieve a perfectly rectangular image even when the projector is not centrally aligned with the screen.

In conclusion, the Eiki LC-XE10 is an outstanding LCD projector that combines high brightness, excellent color performance, and user-friendly features. Its reliable performance and flexible connectivity options make it a perfect choice for anyone looking to deliver impactful presentations or enjoy high-quality visual content.
Top Page Image Contents