Eiki LC-XB200 owner manual Remote Control Operating Range, Remote Control Code

Page 12

Part Names and Functions

Remote Control Battery Installation

1

Open the battery

2

Install new batteries

3

Replace the

compartment lid.

into the compartment.

compartment lid.

 

Press the lid

 

Two AAA size batteries

 

 

 

downward and slide it.

 

For correct polarity

 

 

 

 

 

(+ and –), be sure

 

 

 

 

 

battery terminals are

 

 

 

 

 

in contact with pins in

 

 

 

 

 

compartment.

 

 

To ensure safe operation, please observe the following precautions : ●Use two (2) AAA or LR03 type alkaline batteries.

●Always replace batteries in sets.

Do not use a new battery with a used battery.

Avoid contact with water or liquid.

Do not expose the remote control to moisture or heat.

Do not drop the remote control.

If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.

Risk of an explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions or your local disposal rule or guidelines.

Remote Control Operating Range

Point the remote control toward the projector (Infrared Remote Receiver) when pressing the buttons. Maximum operating range for the remote control is about 16.4'(5 m) and 60 degrees in front of the projector.

16.4' (5 m)

30°

30° Remote control

Remote Control Code

The eight different remote control codes (Code 1–Code 8) are assigned to this projector. Switching the remote control codes prevents interference from other remote controls when several projectors or video equipment next to each other are operated at the same time. Change the remote control code for the projector first before changing that for the remote control. See "Remote control" in the Setting Menu on page 55.

1

While pressing the MENU button, press the IMAGE

button number of times corresponding to the remote

 

control code. See the list below.

2

To initialize the remote control code, slide the RESET/

ON/ALL-OFF switch to RESET, and then to ON. The

 

initial code is set to Code 1.

 

 

 

 

 

 

 

 

 

 

Remote Control Code

 

Number of Times

 

 

 

 

Pressing IMAGE

 

 

 

 

 

Button

 

 

 

Code 1

 

1

 

 

 

Code 2

 

2

 

 

 

Code 3

 

3

 

 

 

Code 4

 

4

 

 

 

Code 5

 

5

 

 

 

Code 6

 

6

 

 

 

Code 7

 

7

 

 

 

Code 8

 

8

 

While pressing the MENU button, press the IMAGE button number of times corresponding to the remote control code.

MENU button

IMAGE button

RESET/ON/ALL-

OFF switch

12

Image 12
Contents Model LC-XB100 LC-XB200 Network SupportedFeatures and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Safety Instructions Air Circulation Installing the Projector in Proper PositionMoving the Projector AC Power Cord Requirement AC Power Cord for the United States and CanadaAC Power Cord for the United Kingdom CompliancePart Names and Functions FrontBack ⑦ ⑧ BottomPart Names and Functions ⑤ LAN Connection Terminal② Point ed 7 8 Volume +/- buttons ⑤ Power indicator⑨ Lamp Replace indicator ① Select buttonPart Names and Functions Remote Control ③ Signal Emission indicatorRemote Control Operating Range Remote Control CodePart Names and Functions Laser Pointer Function Pointer FunctionSpotlight PointerWireless Mouse Operation Connect the USB Infrared Receiver toYour computer Installation Adjustable FeetPositioning the Projector Installation Connecting to a Computer Cables used for connectionInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment Installation Connecting the AC Power Cord Projector side AC outlet sideFor Continental Europe For the U..K Input signal guidance window Basic OperationTurning On the Projector Selected Input Source and Lamp ControlWhat is PIN code? Basic OperationEnter a PIN code PIN Code Input Dialog BoxBasic Operation Turning Off the Projector Basic Operation How to Operate the On-Screen Menu Remote ControlTop Control On-Screen MenuBasic Operation Menu Bar Rgbpc digitalBasic Operation Zoom and Focus Adjustment Auto Setup FunctionKeystone Correction Basic Operation Sound Adjustment Direct OperationMenu Operation Basic Operation Remote Control Operation Timer button No Show buttonImage button Screen buttonComputer Input Input Source Selection RGB Computer 1/Computer 2AnalogInput Menu Top Control Input button Computer Input Computer System Selection Selecting Computer System ManuallyPC System Menu Computer Input Auto PC Adjustment PC adjust MenuTo store adjustment parameters Auto PC adjComputer Input Manual PC Adjustment Reset Mode freeComputer Input StoreComputer Input Image Mode Selection Image select MenuComputer Input Image Adjustment Image Adjust MenuScreen Size Adjustment Screen MenuCustom Position H/VFor zooming in and out the images Digital zoom + Digital zoomTop Control Remote Control Video InputInput Source Selection Video, S-video Input MenuRemote Control Top Control Component RGB ScartVideo Input Video System Selection Video or S-videoAV System Menu Video or S-video Component AV System Menu ComponentVideo Input Image Mode Selection CinemaVideo Input Image Adjustment ColorTint Video Input Store MenuNoise reduction ProgressiveVideo Input Screen Size Adjustment Setting SettingSetting Menu LanguageAuto setup Auto setupInput search Auto KeystonePower off? p.22 TimerKeystone BackgroundDefault Capture Logo PIN code lockCapture Logo PIN code lockChange the Logo PIN code lock setting Enter a Logo PIN codeLogo PIN code change Ceiling RearClosed Caption Power management Shut downOn start Lamp control Lamp life controlRemote control To change the code for the remote controlLarge , Middle or Small , Arrow , Finger or Dot and press To change the code for the projectorKey lock Security Key lock and PIN code lockKey lock PIN code lockChange the PIN code lock setting Change the PIN codeEnter a PIN code Change the PIN code Filter counter FanFan control Filter counterFactory default Filter counter to the factory default settingsLogo , PIN code lock , Logo PIN code lock , Lamp counter Information Input Source Information DisplayMaintenance and Cleaning Indicator is blinking redIndicator lights red Projector is shut down and the WarningMaintenance and Cleaning Cleaning the Filters Resetting the Filter CounterMaintenance and Cleaning Attaching the Lens Cap Cleaning the Projection LensCleaning the Projector Cabinet Maintenance and Cleaning Lamp Replacement Maintenance and Cleaning Service Parts No 343Troubleshooting AppendixAppendix Remote Control does Indicator blinks or lightsWireless Mouse function does not Image is distorted or runs offAppendix Appendix Menu Tree Computer Input/Video InputSound Computer InputSetting Video InputAppendix Indicators and Projector Condition IndicatorsAppendix Compatible Computer Specifications ON-SCREEN ResolutionKHz Panel Resolution Signal CompatibilityPower Mechanical InformationAccessories Optional PartsModel No COMPONENT-VGA Cable AH-98771 SCART-VGA Cable AH-98881Appendix PJ Link Notice Appendix Configurations of Terminals Computer 2 / DVI-I Terminal DIGITAL/ANALOGAppendix PIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Appendix Dimensions Unit mminchEiki International, Inc