Eiki LC-WS250 owner manual Input Source Information Display

Page 59

Information

Input Source Information Display

The Information Menu is used for checking the status of the image signal being projected and the operation of the projector.

Direct Operation

Press the INFO. button on the remote control to display the Information Menu.

Menu Operation

Press the Point ▲▼ buttons to select the Information. The Information Menu is displayed.

See below for displayed information.

Input

The selected input source is displayed.

H-sync freq..

The horizontal frequency of the input signal is displayed in KHz, or - - - -KHzwhen no signal.

V-sync freq..

The vertical frequency of the input signal is displayed in Hz, or - - - - Hz when no signal. Numbers of Hz doubles when during Interlace.

Screen

The selected screen size is displayed.

Language

The selected language is displayed.

Lamp status

The selected lamp mode is displayed.

Lamp counter

The cumulative lamp operating time is displayed.

Power management

Off, Ready, Shut down or Timer is displayed.

Key lock

The selected Key lock icon is displayed.

PIN code lock

Off or On 1 or On 2 is displayed.

Remote control

The selected remote code is displayed.

Remote Control

INFO.. button

ASPECT

Information Menu

59

Image 59

Contents Network Supported Model LC-WS250Features and Design Table of Contents To the Owner Safety PrecautionSafety Instructions Moving the Projector Safety Instructions Air CirculationInstalling the Projector in Proper Position Compliance AC Power Cord for the United States and CanadaAC Power Cord for the United Kingdom ⑧ Exhaust vent Part Names and FunctionsFront Side① LAN Connection Terminal Part Names and Functions Side TerminalTop Panel Part Names and FunctionsPart Names and Functions Remote Control Menu button Image button Remote Control Operating RangeRemote Control Code Two AAA size batteriesPositioning the Projector InstallationAdjustable Feet Cables used for connection Installation Connecting to a ComputerInstallation Connecting to Video Equipment Installation Connecting to Component Video Equipment For the U..S..A.. and Canada Installation Connecting the AC Power CordProjector side AC outlet side For Continental Europe For the U..KSelected Input Source and Lamp Control Input signal guidance windowBasic Operation Turning On the ProjectorPIN Code Input Dialog Box Basic OperationDirect OFF Function Basic Operation Turning Off the ProjectorOn-Screen Menu Basic Operation How to Operate the On-Screen MenuRemote Control Top ControlBasic Operation Menu Bar Keystone Correction Basic Operation Focus AdjustmentAuto Setup Function Mute Basic Operation Sound AdjustmentVolume Volume Dialog BoxBasic Operation Remote Control Operation Screen button Timer buttonNo Show button Image buttonInput Menu Computer InputInput Source Selection Computer 1 RGB Video Computer Input Input Source Selection Computer 2 RGBInput Menu Computer 2 button Computer 2 RGBMode Computer Input Computer System SelectionPC System Menu AutoAuto PC adj Computer Input Auto PC adjustmentPC adjust Menu To store adjustment parametersComputer Input Manual PC adjustment Store Menu Mode free MenuComputer Input Computer Input Image Mode Selection Image adjust Menu Computer Input Image AdjustmentScreen Menu Screen Size AdjustmentCustom adj.. Menu Note Custom adjDigital zoom + Digital zoomVideo button Video button S-video Video InputInput Source Selection Video, S-video Video NoteComponent button Computer 1 RGBComputer 1 Scart Hdmi buttonOr Computer 1Component and then press Video Input Video System SelectionAV System Menu Video or S-video AV System Menu ComponentVideo Input Image Mode Selection Tint Video Input Image AdjustmentImage adjust Menu ColorNoise reduction Off Disabled Lower reduction Higher reduction ProgressiveVideo Input Natural wide Video Input Screen Size AdjustmentZoom WideLanguage SettingSetting Setting Menu Language MenuInput search Auto setupAuto setup Background Power off? p.20Timer KeystoneLogo select Logo Logo and Logo PIN code lock settingsDefault Logo selectOff Logo PIN code lock Capture Logo PIN code lockCapture Logo PIN code change Change the Logo PIN code lock settingEnter a Logo PIN code Logo PIN code change Enter a Logo PIN codeCeiling Rear Hdmi setupPower management Power managementStandby mode Count down Min . Only set to Count down , Timer isDirect on NoteFrom Color to White Note Closed captionOff , CC1 , CC2 , CC3 or CC4 To change the code for the projector Remote controlLamp control Security Key lock and PIN code lock Enter a PIN code Change the PIN code Lamp counter Video delay controlFan Fan controlFilter counter Factory defaultFactory default Filter counterInput Source Information Display InformationNote Then check the matters below Maintenance and CleaningProjector is shut down and the Warning indicator lights red Filter counter Reset? Maintenance and Cleaning Replacing the FilterResetting the Filter Counter Cleaning the Projector Cabinet Maintenance and Cleaning Attaching the Lens CoverCleaning the Projection Lens Top Panel Reset the lamp counterService Parts No 349 Lamp replacement counter Reset? appears Maintenance and Cleaning Resetting the Lamp CounterPress Select button. Lamp replacement counter Appendix TroubleshootingColor is strange AppendixNo image No soundPIN code dialog box appears Remote Control doesIndicator blinks or lights Image is distorted or runs offAppendix Menu Tree Information SettingIndicators Appendix Indicators and Projector Condition Note Appendix Compatible Computer SpecificationsFreq Appendix Technical Specifications COMPONENT~VGA Cable AH-98771 SCART~VGA Cable AH-98881 Appendix Optional PartsPJ Link Notice Model NoHdmi 19 PIN Type a Appendix Configurations of TerminalsControl Port Connector D-sub 9 pin Terminal Analog RGB Mini D-sub 15 pinLogo PIN Code Lock No Appendix PIN Code Number MemoPIN Code Lock No Unit inchmm Appendix DimensionsEiki International, Inc