Eiki LC-W4 instruction manual Basic Operation, Turning on / OFF Projector, Turning on Projector

Page 21

BASIC OPERATION

TURNING ON / OFF PROJECTOR

TURNING ON PROJECTOR

1

Complete peripheral connections (with Computer, VCR, etc.)

 

before turning on projector. (Refer to "CONNECTING TO

 

PROJECTOR" on Pages 12~15 for connecting that equipment.)

2

Connect a projector's AC Power Cord into a wall outlet and turn

 

MAIN ON / OFF SWITCH to ON. LAMP indicator lights RED,

 

and READY indicator lights GREEN.

3

Press POWER ON-OFF button on Top Control or on Remote

 

Control Unit to ON. LAMP indicator dims, and Cooling Fans start

to operate. Preparation Display appears on a screen and count- down starts. Signal from source appears after 30 seconds. Current Input position and Lamp status are also displayed on screen for 5 seconds. (Refer to "LAMP MANAGEMENT" on page 45.)

LAMP STATUS

INPUT 1

1 2

30

Preparation Display disappears after 30 seconds.

TURNING OFF PROJECTOR

1

2

3

Press POWER ON-OFF button on Top Control or on Remote Control Unit, and a message "Power off?" appears on a screen.

Press POWER ON-OFF button again to turn off projector. LAMP indicator lights bright and READY indicator turns off. After approximate 90 seconds, READY indicator will light green again and projector may be turned on by pressing POWER ON-OFF button.

Cooling fans will operate for approximate 2 minutes after projec- tor is turned off. To power down completely, turn MAIN ON/OFF SWITCH to OFF and disconnect AC Power Cord.

TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.

Power off?

Message disappears after 4 seconds.

When Power Management function mode is Ready or Shut down, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power Management” on pages 39 and 40.

When WARNING TEMP. indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on projector again.

When both WARNING TEMP. and READY indicators to flash, follow procedures below:

1.Turn MAIN ON / OFF SWITCH to OFF.

2.Turn a projector on again.

When WARNING TEMP. indicator continues to flash, follow procedures below:

1.Turn MAIN ON / OFF SWITCH to OFF and disconnect AC Power Cord from an AC outlet.

2.Check Air Filters for dust accumulation.

3.Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 44.)

4.Turn a projector on again.

If WARNING TEMP. indicator should still continue to flash, contact sales dealer where you purchased this projector or service center.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Multimedia Projector Model LC-W4Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compatibility Features and DesignName of Each Part of Projector PreparationSETTING-UP Projector Connecting AC Power CordFor U.S.A. and Canada For Continental Europe Preparation Lens Installation Lens Shift AdjustmentPositioning Projector Moving Projector Preparation Picture Level and Tilt AdjustmentConnecting Projector Replacement of TerminalTerminals of Projector Input 1, 2 Connecting Projector INPUT/OUTPUT Terminals and Jacks InputAudio Output Jacks Terminals of a Projector Connecting to Computer2INPUT Terminals of a Projector Connecting to Video EquipmentBefore Operation TOP Controls and IndicatorsOperation of Remote Control Laser Pointer FunctionLaser Pointer Drag on Select Button Remote Control Batteries InstallationHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Guide Window Before Operation Menu BARTurning on / OFF Projector Basic OperationTurning on Projector Turning OFF ProjectorZoom Adjustment Adjusting ScreenFocus Adjustment Keystone AdjustmentTimer Function Basic Operation Picture Freeze FunctionNo Show Function Direct Operation Sound AdjustmentMenu Operation Sound MenuSelecting Input Source Computer InputSelecting Computer System InputSelect Computer System Manually Computer Input Automatic MULTI-SCAN SystemAuto PC System MenuResolution Computer Input Compatible Computer SpecificationsAuto PC Adjustment PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Display area Display area HFull screen Image Level Select Direct Picture Image AdjustmentImage Level Select Menu Image Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Input When Select Input 3 AV TerminalAuto Selecting Video SystemAV System Menu Video or S-VIDEO AV System Menu Component VideoCinema Color Video Input Image Level AdjustmentTint Progressive scanNatural wide ZoomSetting Setting MenuSetting Menu Power management Lamp ModeOn start Wireless Mouse mode To change the code of the Remote Control UnitProjector mode To change the code of ProjectorFactory default Lamp counter resetMaintenance Operating Wireless MouseInstallation Operating Wireless MouseCleaning Projection Lens Appendix AIR Filter Care and CleaningYellow Lamp Dim Lamp Red Lamp Mark on Lamp Appendix Lamp ManagementFigure shows case of replacing Lamp Appendix Lamp ReplacementLamp Handling Precautions Troubleshooting Service Appendix Indicators and Projector Condition Indicators Projector ConditionComputer Input Appendix Menu TreeVideo Input Computer Input/Video Input Technical Specifications DVI-I Terminal DIGITAL/ANALOG Appendix Configurations of TerminalsAppendix Key to better communications Canada LCD Projector Lens Replacement and Installation Procedure Fig-4 Fig-8 Fig-9 Focus Adjustment For Model LNS-W03 and LNS-W07 Correcting the focus Model No Zoom 100 120 150 180 200 250 300 350 400 500 600 Screen Size inch and Throw Distance mLens Shift Center Ratio
Related manuals
Manual 64 pages 56.67 Kb
Top Page Image Contents