Intel I945P specifications Hyper-Threading Technology

Page 38

BIOS

Hyper-Threading Technology

Enables the CPU Hyper-Threading Technology.

Options: Enables, Disabled.

It is recommend to enable Hyper-Threading Technology on system with Windows XP and Linux 2.4 and disabling it for legacy OS.

First /Second/Third/Other Boot Device

The BIOS attempts to load the operating system from the devices in the sequence selected in these items.

Options: Floppy, LS120, Hard Disk, CDROM, ZIP100, USB-FDD, USB-CDROM, LAN, Disabled.

Boot Other Device

When enabled, the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the first, second, and third boot devices.

Options: Enabled, Disabled.

Boot Up Floppy Seek

If this item is enabled, it checks the size of the floppy disk drives at start-up time. You don’t need to enable this item unless you have a legacy diskette drive with 360K capacity.

Options: Enabled, Disabled.

Boot Up NumLock Status

This controls the state of the NumLock key when the system boots. The default is On. On: The keypad acts as a 10-key pad.

Off: The keypad acts like cursor keys.

Security Option

This category allows you to limit access to the System and Setup, or just to Setup. The default is Setup.

System: The system will not boot and access to Setup will be denied unless the correct password is entered at the prompt.

Setup: The system will boot, but access to Setup will be denied unless the correct password is entered at the prompt.

APIC Mode

This item allows you to enable APIC (Advanced Programmable Interrupt Controller)

Page 4-4

Image 38
Contents Manual Revision October 25 Disclaimer of Warranties Post Port Frequently Asked Questions Table of Contents Section Driver Installation Left Blank Introduction Mainboard Features Ultra ATA100 Special Features Bios Features Magic Health System Block Diagram Introduction Chipset SpecificationMainboard Specification Processor Main MemoryIDE AudioAt Rear Panel Onboard connector and pin-headerPeripheral Interfaces Front Panel ControllerSupported Operating System Specification Special FeaturesForm Factor Installation Mainboard LayoutInstallation Easy Installation Procedure CPU InstallationStep Installation Jumper Settings Settings Normal Default Clear CmosSupported Configuration Installation System Memory Configuration Dual Channel interfaceMemory configurations supported Memory InstallationInstallation VGA Card Installation PCI-E VGA Card Installation Device Connectors Jcpufan / Jpwrfan / JsysfanPW1 GND CUSB3 CUSB4 CFP CIR Cspk Installation Thermo Stick Function Optional Installation Acpi S3 Suspend To RAM Function Installation Acpi S3 Suspend To RAM Function Installation To enter the Setup Program Main MenuStandard Cmos Setup Standard Cmos SetupAdvanced Bios Features Bios Features SetupHyper-Threading Technology Advanced Chipset Features Chipset Features SetupDram Timing Selectable Integrated Peripherals PCI Express FunctionChipset IDE Devices Chipest Serial ATA Setting Legacy Devices Parallel Port Mode Power Management Setup Power ManagementPCI-E device PME function Options Enabled, Disabled Wake-Up by PCI Card PNP/PCI/PCI-E Configuration PCI Express related itemsInterrupt requests are shared as shown below PC Health StatusDisplays the current system/CPU temperature Smart Fan example Power Bios Features PowerBOIS FeaturesCPU CLOCK/SPEED Voltage Adjust Menu Load Optimized Defaults Defaults MenuLoad Fail-Safe Defaults Enter Password Supervisor/User Password SettingSave to Cmos and Exit Y/N? Y Exiting BiosSave & Exit Setup Exit Without SavingDrivers Installation Easy Driver InstallationDrivers Installation Realtek Sound Manager Quick User-guide Sound EffectDrivers Installation Speaker Configuration Above shows the phone jack setup for 8 channel modeDrivers Installation General SpdifDrivers Installation Audio Wizard Audio WizardDrivers Installation Flashing the Bios AppendixKey in File Name to save previous Bios to file Appendix B Appendix Appendix If password is set, ask for password