Intel PCM-6896 manual Sdram RAS Precharge Time, System Bios Cacheable, Video Bios Cacheable

Page 67

SDRAM RAS Precharge Time

If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast gives faster performance; slow gives more stable performance. This field applies only when synchronous

DRAM is installed in the system.

System BIOS Cacheable

Selecting Enabled allows caching of the system BIOS ROM at F0000h- FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The choices:

Enabled, Disabled

Video BIOS Cacheable

Selecting Enabled allows caching of the video BIOS ROM at C0000h to C7FFFh, resulting in better video performance. However, if any program writes to this memory area, a system error may result. The choices:

Enabled, DisabledMemory

Hole At 15-16m

In order to improve performance, certain space in memory is reserved for ISA cards. This memory must be mapped into the memory. The choices:

15-16 M, disabled

CPU Latency Timer

During enable, a deferrable CPU cycle will only be Deferred after it has been in Snoop Stall for 31 clocks and another ADS# has arrived. During disable, a deferrable CPU cycle will be deferred immediately after the

GMCH recieves another ADS#.

Delayed Transaction

The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1.

Image 67
Contents PCM-6896 Acknowledgments Copyright NoticeFCC Statement Packing ListMessage to the Customer Aaeon Customer ServicesProduct Warranty Dear Customer Contents AwardBIOSetup Driver Installation General Information Introduction Features Specifications Page Audio Interface Chipset 815E SDD Interface Board Layout Board Dimensions Installation Removing the CPU Safety precautionsInstalling a CPU Open Closed Setting jumpersSystem Memory Installing Dram DIMMsLocation of Jumpers & Connectors Jumpers List of JumpersConnectors List of ConnectorsClear Cmos Selection JP1 JP2 & JP3 For COM3 & COM4 Selec- tion Speaker Out and Line out JP4 Front Panel Connectors JP5PC/104 Plus Voltage Select JP6 RS-232/422/485 COM 2 JP8, JP7 CPU/SDRAM Speed Select JP9 DiskOnChip socket Configure DOC as a boot device DiskOnChip DOC 2000 InstallationDiskOnChip Address Selection JP10 CPU Fan Power Connector CN1 USB Connector CN5 & CN6 Primary IDE Hard Drive Connector CN7 IDE Hard Drive Connectors CN7IDE Hard Drive Connector CN7 IDE Hard Drive Connector CN7ATX Power Connector CN11 IR Connector CN10Digital Visual Interface Connector CN12 Keyboard and Mouse Connector CN13 VGA Display Connector CN14 Audio Connector CN15 Base-Tx Ethernet Connector CN17 Connecting the floppy drive Floppy drive connector CN19Floppy Drive Connector CN19 Digital I/O Connector CN20 Audio Out Connector 1 Watt CN22 Compact Flash Connector Compact Flash ConnectorAward Bios Setup To Enter Setup Before Boot Press DEL KEY Starting setupGetting help Case of ProblemsThese keys helps you navigate in Setup Setup keysPower Management Setup Standard Cmos FeaturesAdvanced Bios Features Advanced Chipset FeaturesSet Supervisor/User Password PnP/PCI ConfigurationLoad Fail-Safe Defaults Load Optimized DefaultsDate and Time Configuration Standard Cmos FeaturesPage Drive a Drive B Memory Halt OnBase Memory Other Memory Extended MemoryVirus Warning Advanced Bios FeaturesCPU Internal Cache/External Cache Swap Floppy Drive OS Select For DRAM64MB-Select Typematic Rate Setting- Key strokes repeat at aTypematic Dealy Msec- Sets the delay time Typematic Rate Chars/Sec- Sets the numberReport No FDD For WIN 95- Wheather report HDD S.M.A.R.T CapabilitySdram RAS-to-CAS Delay Advanced Chipset Features Sdram CAS Latency TimeSdram Cycle Time Tras/Trc Delayed Transaction System Bios CacheableVideo Bios Cacheable CPU Latency TimerSystem Memory Frequency Paging Mode ControlAGP Graphics Aperture Size Display Cache FrequencyRas# Timing RAS-to-CAS OverrideRas# Precharge Timing IDE Primary/Secondary Master/Slave PIO Integrated PeripheralsOn-Chip Primary PCI IDE On-Chip Secondary PCI IDEUSB Controller IDE HDD Block ModePower on Function KB Power on PasswordOnboard FDC Controller Hot Key Power OnUart Mode Select UART2 Duplex ModeOnboard Parallel Port Parallel Port ModeECP Mode Use DMA Onboard Serial Ports 1, 2,3,4Watch Dog Timer Power Management Power Management SetupAcpi Function Video Off Method Suspend Type Suspend ModeHDD Power Down Video Off In SuspendResume By Alarm Power On By RingReload Global Timer Events Resources Controlled By PnP/PCI ConfigurationsPnP OS Installed Reset Configuration DataPC Health Status Shutdown TemperatureSpread Spectrum Clock By Slight AdjustFrequency/Voltage Control Auto Detect DIMM/PCI CLKLoad Fail-Safe Defaults Load Optimized Default Load Optimized DefaultEnter Password Set Supervisor PasswordSet User Password Save to Cmos and Exit Save to Cmos and ExitQuit without Saving Drivers Installation Installing Drivers Installing Chipset Driver for Windows 95/98 Installing Ultra ATA Storage Driver for Windows 95/98 ==Select the Optional Search for best Lan driver Installing LAN for Windows 95/98Installing VGA for Windows 95/98 Installing Audio for Windows 95/98 Please perform this procedure first Installing Security Driver for Windows NTInstalling Ultra ATA Storage Driver for Windows NT Installing VGA for Windows NT Installing Audio for Windows NT ==Intel Pro Adapter will appear ==Click on OK Installing LAN for Windows NTInstalling VGA for Windows Installing Audio for Windows Installing LAN for Windows