Intel 945GZ, 945GC ・ Video off Method, ・ Video Off In Suspend, ・ Suspend Type, ・ Modem Use IRQ

Page 32

Intel 945 Series

User's Manual

 

 

・Video off Method

 

This selection will cause the system to turn off the vertical and

V/HSYNC+Blank

horizontal synchronization ports and write blanks to the video

 

buffer.

Blank Screen

This option only writes blanks to the video buffer.

DPMS Support

Initial display power management signaling.( default)

・Video Off In Suspend

This determines the manner in which the monitor is blanked. The choices are Yes Video will off and No Video always on.

・Suspend Type

This item allows you to select ACPI Suspend Type.

・MODEM Use IRQ

This determines the IRQ in which the MODEM can use. Default option is IRQ3.

・Suspend Mode

If system activity is not detected for the length of time specified in this field, all devices except CPU will be shut off. Select [Disabled] can not suspend.

・HDD Power Down

If HDD activity is not detected for the length of time specified in this field, the HDD will be shut off.

・Soft-Off by PWR-BTTN

Pressing the power button for more than 4 seconds forces the system to enter the Soft- Off state.

・CPU THRM-Throttling

This option allows you to adjust the CPU temperature. If the CPU temperature gets to the temperature you set, CPU frequency will be throttling. The range is 12.5% to 87.5%, increase by 12.5%.

・Wake-Up by PCI card

When set to [Enabled], the feature allows your system to be awakened from the Power saving modes through any event on PCI device.

・Power On by Ring

During Disabled, the system will ignore any incoming call from the modem. During Enabled, the system will boot up if there's an incoming call from modem.

・Resume by Alarm

The field is used to enable or disable the feature of booting up the system on a scheduled time/date.

・Date (of Month) Alarm

[0]: This option power-on the system everyday according to the time set in the “Time (hh:mm:ss) Alarm” item.

[1-31]:This option selects a date you would like the system to power-on. The system will power-on on the date set, and the time set in the “Time (hh:mm:ss) Alarm” item.

・Time (hh:mm:ss) Alarm

This item sets the time you would like the system to power-on.

・Primary/ Secondary IDE 0/1

When the Primary/Secondary IDE 0/1 devices are activity, whether cancel PC and IDE saving mode.

・FDD, COM, LPT Port

When the FDD, COM, LPT Port are activity, whether cancel the PC and IDE saving mode.

・PCI PIRQ[A-D]#

This option is for setting PCI PIRQ.

- 31 -

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Intel 945 Series Disclaimer CopyrightTable of Contents Package Checklist IntroductionSpecifications CPUMainboard Layout Intel 945GCV1.0 This picture is only for referenceIntel 945GCV2.0 This picture is only for reference Connecting Rear Panel I/O Devices AUDIO1Installing Mainboard Choosing a Computer ChassisInstallation of the CPU and CPU Cooler Installation of the CPUDual-Channel Memory installation For Intel 945GCV2.0 Only Installation of Memory ModulesInstallation of the CPU Cooler Connecting Peripheral Devices Floppy and IDE Disk Drive ConnectorsSerial ATA Connectors PCI and PCI Express slotsCmos Memory Clearing Header Checking Jumper SettingsKeyboard Power FunctionJKB FAN Power Connectors Front Panel Switches & Indicators HeadersAdditional USB Port Headers Front Panel Audio Connection HeaderInternal Audio Connectors ATX Power Input ConnectorsAbout Bios Setup To Run Bios SetupPost Power On Self Test About CmosBios Setup Cmos Setup Utility Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor Password Set User Password・ Date mmddyy ・ Time hhmmssIDE Channel 0 Master/Slave,SATA Channel 1~4 Access Mode IDE HDD Auto-DetectionCapacity CylinderCPU Feature Delay Prior to ThermalExecute Disable Bit ・ Quick Power On Self Test・ Boot Up Floppy Seek ・ Boot Up NumLock Status・ Singal CPU Work Mode ・ Security Option・ MPS Version Control For OS ・ OS Select For Dram 64MB・ System Bios Cacheable ・ Video Bios CacheablePCI-E Compliancy Mode ・ SLPS4# Assertion Width・ Dvmt Mode ・ On-Chip Frame Buffer SizeIDE HDD Block Mode IDE DMA transfer accessOnChip IDE Device On-Chip Primary PCI IDESata Port Speed Settings Pata IDE ModeBack to Integrated Peripherals Setup Menu Onboard Device IDE Primary Master/Slave Udma AutoBios Write Protect Back to Integrated Peripherals Setup Menu Super IO DevicePower on Function USB ControllerParallel Port Mode EPP Mode SelectECP Mode Use DMA ・ Hot Key Power on・ Acpi Suspend Type ・ Power Management・ Acpi Function ・ Suspend Mode ・ HDD Power Down・ Power On by Ring ・ Resume by Alarm・ Reset configuration data ・ Init Display First・ Resource controlled by ・ IRQ Resources・ Shutdown Temperature ・ Smart FAN Control・ FAN Target Temperture ・ FAN Min Speed・ System Memory Control ・ CPU Voltage Regulator・ Dram Voltage Regulator ・ Auto Detect PCI ClkSet Supervisor/User Password Enter PasswordPassword DISABLED！ Driver Installation
Top Page Image Contents