Intel 945GCT, 945GZT user manual Installation of Memory Modules, Installation of the CPU Cooler

Page 11
Ejector Tab

Intel 945 Series

User's Manual

 

 

2.3.2 Installation of the CPU Cooler

For proper installation, please kindly refer to the instruction manuals of your CPU Cooler.

2.4 Installation of Memory Modules

This mainboard provides two 240-pin DDRII (Double Data Rate) DIMM slots (Intel945GC(V2.0) provides 4x) , and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install two identical (the same brand, speed, size and chip- type) memory modules in the DDRII DIMM slots to activate Dual Channel Memory Technology. Otherwise, it will operate at single channel mode.

Static electricity can damage the electronic components of the computer or optional boards. Before starting these procedures, ensure that you are discharged of static

electricity by touching a grounded metal object briefly.

To install system memory:

1. Power off the computer and unplug the Mounting NotchNotch Key AC power cord before installing or

removing memory modules.

2.Locate the DIMM slot on the board.

3.Hold two edges of the DIMM module carefully, keep away from touching its

connectors.Rib

4. Align the notch key on the module with the rib on the slot.

5.Firmly press the module into the slots until the ejector tabs at both sides of the slot automatically snap into the mounting notch. Do not force the DIMM module in with extra force as the DIMM module only fits in one direction.

6.To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and then pull out the DIMM module.

Dual-Channel Memory installation (For Intel 945GC(V2.0) Only)

The Intel 945GC(V2.0) includes 4 DIMM sockets, and each Channel has two DIMM sockets as following:

Channel 1 : DIMM1, DIMM2

Channel 2 : DIMM3, DIMM4

The following is a Dual Channel Memory configuration table: (D: Double Side, S: Single Side, "--": Empty)

 

Channel 1

 

Channel 2

Dual Channel

DIMM1

 

DIMM2

DIMM3

 

DIMM4

 

S

 

--

S

 

--

Enabled

S

 

--

--

 

S

Enabled

 

 

 

 

 

 

 

--

 

S

S

 

--

Enabled

--

 

S

--

 

S

Enabled

S

 

S

S

 

S

Enabled

D

 

--

D

 

--

Enabled

D

 

--

--

 

D

Enabled

--

 

D

D

 

--

Enabled

 

 

 

 

 

 

 

--

 

D

--

 

D

Enabled

- 10 -

Image 11
Contents Intel 945 Series Copyright DisclaimerTable of Contents Introduction Package ChecklistCPU SpecificationsIntel 945GCV1.0 This picture is only for reference Mainboard LayoutIntel 945GCV2.0 This picture is only for reference AUDIO1 Connecting Rear Panel I/O DevicesChoosing a Computer Chassis Installing MainboardInstallation of the CPU Installation of the CPU and CPU CoolerDual-Channel Memory installation For Intel 945GCV2.0 Only Installation of Memory ModulesInstallation of the CPU Cooler PCI and PCI Express slots Connecting Peripheral DevicesFloppy and IDE Disk Drive Connectors Serial ATA ConnectorsCmos Memory Clearing Header Checking Jumper SettingsKeyboard Power FunctionJKB Front Panel Switches & Indicators Headers FAN Power ConnectorsFront Panel Audio Connection Header Additional USB Port HeadersATX Power Input Connectors Internal Audio ConnectorsAbout Cmos About Bios SetupTo Run Bios Setup Post Power On Self TestBios Setup Cmos Setup Utility Set User Password Load Fail-Safe DefaultsLoad Optimized Defaults Set Supervisor Password・ Time hhmmss ・ Date mmddyyCylinder IDE Channel 0 Master/Slave,SATA Channel 1~4 Access ModeIDE HDD Auto-Detection CapacityDelay Prior to Thermal CPU Feature・ Boot Up NumLock Status Execute Disable Bit・ Quick Power On Self Test ・ Boot Up Floppy Seek・ OS Select For Dram 64MB ・ Singal CPU Work Mode・ Security Option ・ MPS Version Control For OS・ SLPS4# Assertion Width ・ System Bios Cacheable・ Video Bios Cacheable PCI-E Compliancy Mode・ On-Chip Frame Buffer Size ・ Dvmt ModeOn-Chip Primary PCI IDE IDE HDD Block ModeIDE DMA transfer access OnChip IDE DeviceIDE Primary Master/Slave Udma Auto Sata Port Speed SettingsPata IDE Mode Back to Integrated Peripherals Setup Menu Onboard DeviceUSB Controller Bios Write ProtectBack to Integrated Peripherals Setup Menu Super IO Device Power on Function・ Hot Key Power on Parallel Port ModeEPP Mode Select ECP Mode Use DMA・ Acpi Suspend Type ・ Power Management・ Acpi Function ・ Resume by Alarm ・ Suspend Mode・ HDD Power Down ・ Power On by Ring・ IRQ Resources ・ Reset configuration data・ Init Display First ・ Resource controlled by・ FAN Min Speed ・ Shutdown Temperature・ Smart FAN Control ・ FAN Target Temperture・ Auto Detect PCI Clk ・ System Memory Control・ CPU Voltage Regulator ・ Dram Voltage RegulatorEnter Password Set Supervisor/User PasswordPassword DISABLED! Driver Installation